Outdoor Mouse Bait Station - Tool-Free, Rainproof, Zip-Tie Lock (Skull Lid + Plain Lid)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Tool-free, rainproof outdoor mouse bait station. Snap lid, one zip tie to lock it, no supports. Skull and plain lids.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 5
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor & Garden
- Licencja
- Creative Commons — Attribution — Noncommercial
TOOL-FREE OUTDOOR MOUSE BAIT STATION
A compact, weather-resistant bait station for mice that prints on any FDM printer with NO supports. Two parts: a base and a lid. The lid snaps on and is locked with a single zip tie - no screws, no tools needed.
HIGHLIGHTS
No tools needed: the lid snaps on and one cable tie (slot built in) locks it shut.
Rainproof: overlapping lid lip plus rain walls over both entrances.
Wall-hugging: entrances and the closing side face the wall, so the box can sit flush against it. 2 screw holes if you want to fix it down.
Tamper-resistant: bait sits behind a 65 mm passage with 30 x 30 mm entrances.
Holds 2 bait blocks (32 x 32 x 26 mm, about 5 mm centre hole) on pins, plus loose pellets.
Flat floor, no supports, about 120 g of filament.
Remix-friendly: all STL files are included.
TWO VERSIONS, SAME BASE
Skull lid (main version): two-colour lid with a POISON stencil and skull-and-crossbones warning, black + white filament.
Plain lid: single colour, no markings.
DIMENSIONS
Outer size 120 x 92 x 45 mm (lid 125 mm wide). Two 4.2 mm mounting holes, 98 mm apart.
PRINT SETTINGS (TESTED)
Printer: Anycubic Kobra S1, 0.4 mm nozzle, textured PEI plate. The 3MF files are ready to slice.
Layer height 0.24 mm, 3 walls, 20 % infill, 4 bottom layers. No supports, no brim. Seam gap 5 %.
The base prints upright. The lid prints top face down on the bed (already set up in the 3MF).
PLA at 220 C, fan minimum 70 %. For permanent outdoor use PETG or ASA is recommended, because PLA softens in direct sun.
Other printers: use the STL files (base + lid; for the skull lid also the inlay STL, which is the white part).
ASSEMBLY
Place the bait blocks on the pins and add pellets.
Hook the wall-side lip of the lid under the base lip, then press the free side down until the snap tab clicks in.
Thread a zip tie through the lug and the slot to lock it.
To open: cut the zip tie, pull the snap tab out, lift the free side slightly while pulling the lid toward you, then lift it off.
FIT NOTE
Clearances are tight (0.1-0.25 mm). If your printer runs over-sized and the lid is too stiff, lightly sand the lip or scale the lid to 99.7 %.
SAFETY
Rodenticides are hazardous. Keep bait stations out of reach of children, pets and wildlife, follow the bait manufacturer's label and your local regulations, and wear gloves when handling bait. This is a printed container, not a certified product.
LICENSE
Own design, not a remix. Free to share and remix with credit, non-commercial use only (CC BY-NC).