1 / 4
52 mm gauge pod for VW Golf 3 (Golf III, Mk3) and Vento, 1991–1997 – accessory slot, no drilling — zdjęcie 1
1 / 4

52 mm gauge pod for VW Golf 3 (Golf III, Mk3) and Vento, 1991–1997 – accessory slot, no drilling

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Pod for one 52 mm gauge, plugs into the accessory slot under the heater controls of a VW Golf 3 / Vento. No drilling.

Ocena
0 / 5
Polubienia
1
Pobrania
2
Wydruki
0
Wyświetlenia
17
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial

Plugs into a blank slot below the heater controls of a Golf 3 instead of a cap and holds one 52 mm gauge flush.

For the VW Golf 3 (also called Golf III or Golf Mk3, type 1H), including GTI, VR6 and Vento: the pod plugs into an accessory slot below the heater and fan controls instead of a blank cap and holds one 52 mm gauge flush – e.g. oil temperature on the VR6 or boost on the TDI.

  • A hollow plug with crush ribs clamps in the slot like the original cap. Nothing is drilled.

  • The gauge sits flush in the pod, held by crush ribs without screws.

  • The cable runs through the plug behind the console.

  • Variants for 45, 50 and 55 mm gauge depth.

  • Prints face-down on the bed: smooth visible side, no supports.

The slot is only 27 mm tall, so the pod sits in front of the console and protrudes by the gauge depth.

Designed for

  • VW Golf 3, 1H, 1991–1997

  • Trims: GTI, VR6, TDI, GT, Vento, Variant

  • Slot size taken from the original part (Printables 1080985, CC BY). Golf 3 Cabrio (1E) with the same dashboard not confirmed. Passenger airbag standard from 1995 – in the dashboard top, not here.

Variants (all included)

  • Gauge up to 45 mm deep

  • Gauge up to 50 mm deep

  • Gauge up to 55 mm deep

Gauge bore: 52.79 mm (52 mm gauges, +0.4 mm clearance).

Included

  • STL, 3MF and STEP for every variant

  • 52 mm tolerance test ring – print it first

  • README with print settings and installation (EN/DE)

Safety

The slot sits below the heater controls, clear of the airbag zones. The pod must not obstruct the gear lever or heater controls – check in every gear.

Fit

File the crush ribs if needed; too loose: felt tape on the plug. Bore +0.4 mm, check with the test ring. Dimensions taken from published sources: Printables 1080985 by zazaw1zard (CC BY 4.0); only measurements were used, no geometry. Not yet tested on the vehicle.

How it's made

Parametric CAD (build123d, Python), exact solids. The CAD code was written with an AI assistant and checked by us; no AI-generated meshes. Renders are made from the CAD in Blender.

License

CC BY-NC 4.0: you may share and adapt it for non-commercial purposes, as long as you credit Magmacode and link the license (https://creativecommons.org/licenses/by-nc/4.0/). Commercial sale of printed parts only by written agreement with Magmacode.

Not an original part, no affiliation with any vehicle manufacturer.

Tagi