52 mm gauge pod for VW Golf 3 (Golf III, Mk3) and Vento, 1991–1997 – accessory slot, no drilling
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Pod for one 52 mm gauge, plugs into the accessory slot under the heater controls of a VW Golf 3 / Vento. No drilling.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 2
- Makes
- 0
- Views
- 23
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- Creative Commons — Attribution — Noncommercial
Plugs into a blank slot below the heater controls of a Golf 3 instead of a cap and holds one 52 mm gauge flush.
For the VW Golf 3 (1H), including GTI, VR6 and Vento: the pod plugs into an accessory slot below the heater and fan controls instead of a blank cap and holds one 52 mm gauge flush – e.g. oil temperature on the VR6 or boost on the TDI.
A hollow plug with crush ribs clamps in the slot like the original cap. Nothing is drilled.
The gauge sits flush in the pod, held by crush ribs without screws.
The cable runs through the plug behind the console.
Variants for 45, 50 and 55 mm gauge depth.
Prints face-down on the bed: smooth visible side, no supports.
The slot is only 27 mm tall, so the pod sits in front of the console and protrudes by the gauge depth.
Designed for
VW Golf 3, 1H, 1991–1997
Trims: GTI, VR6, TDI, GT, Vento, Variant
Slot size taken from the original part (Printables 1080985, CC BY). Golf 3 Cabrio (1E) with the same dashboard not confirmed. Passenger airbag standard from 1995 – in the dashboard top, not here.
Variants (all included)
Gauge up to 45 mm deep
Gauge up to 50 mm deep
Gauge up to 55 mm deep
Gauge bore: 52.79 mm (52 mm gauges, +0.4 mm clearance).
Included
STL, 3MF and STEP for every variant
52 mm tolerance test ring – print it first
README with print settings and installation (EN/DE)
Safety
The slot sits below the heater controls, clear of the airbag zones. The pod must not obstruct the gear lever or heater controls – check in every gear.
Fit
File the crush ribs if needed; too loose: felt tape on the plug. Bore +0.4 mm, check with the test ring. Dimensions taken from published sources: Printables 1080985 by zazaw1zard (CC BY 4.0); only measurements were used, no geometry. Not yet tested on the vehicle.
How it's made
Parametric CAD (build123d, Python), exact solids. The CAD code was written with an AI assistant and checked by us; no AI-generated meshes. Renders are made from the CAD in Blender.
License
Personal use only. Please do not resell the files or printed parts. Dimensions from published sources, not yet tested on the vehicle. Not an original part, no affiliation with the vehicle manufacturer (VW). Brand and model names are used only to indicate the intended vehicle.
Deutsch: Steckt statt einer Blindkappe im Steckplatz unter der Heizungsbedienung des Golf 3 und hält ein 52-mm-Instrument bündig. Alle Varianten als STL/3MF/STEP, Testring und Anleitung DE/EN enthalten. Private Nutzung, kein Weiterverkauf von Dateien oder Drucken.
Settings
Material: ASA (or PA12, ABS). No PETG, no PLA – the interior gets very hot, even in the shade.
Layer height 0.2 mm, 4 walls, 20 % infill, no supports.
Orientation: Face (visible side) down on the bed, plug pointing up.
Print time approx. 5 h 08 min, about 57 g (default variant).
Print the 52 mm tolerance test ring first to check the gauge fit on your printer.
Installation 1. Lever the blank cap out of the slot. 2. Route the cable through the groove into the plug and behind the console, press the gauge in from the front. 3. Push the pod straight into the slot until it sits against the console.
