1 / 4
Ridgeline Tent Stake Set – 6 Two-Color Tent Stakes + Stake Puller — zdjęcie 1
1 / 4

Ridgeline Tent Stake Set – 6 Two-Color Tent Stakes + Stake Puller

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Six 180 mm T-beam tent stakes with hooked guy-line notches + J-hook stake puller. Two-color, flat print, no supports.

Ocena
0 / 5
Polubienia
1
Pobrania
0
Wydruki
0
Wyświetlenia
7
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Standard Digital File License

Lightweight, support-free camping stakes you can print in one plate. The Ridgeline Tent Stake Set has six 180 mm tent stakes plus a T-handle stake puller. Every part prints flat on its back with no supports. The second color comes from the shapes themselves: solid blue head caps, two flush "trail" stripes inlaid in each stake, three mountain-peak chevrons on the puller grip and a blue hook tip. There is no text or logo anywhere. Bright heads are easy to spot in grass, so you leave fewer stakes behind at the campsite.

How it works

  • T-beam stake: a 3.0 mm flat plate with a centre rib that tapers from 10.0 mm at the head to 3.4 mm at the point. This gives the stake stiffness without much weight.

  • - Two hooked guy-line notches on the head (4.1 mm wide, 9.5 mm deep, angled 40° back toward the head), so the line stays put under tension.

  • - Ø11.0 mm hole through the head for the puller hook, a cord loop or a pull tab.

  • - Stake puller: put the J-hook tip through the head hole and pull straight up. The 13.0 mm throat wraps the 10 mm hea

d with 3.0 mm clearance, and the 7 × 7 mm hook bar (9.9 mm diagonal) passes through the Ø11.0 hole. You can also use the 100 mm T-grip to push stakes in by hand.

Main dimensions (measured from the model, mm)

  • Stake: 180.0 L × 24.0 W (head) × 10.0 H; shaft plate 15.0 wide × 3.0 thick; rib 5.0 wide; point 2.2 wide

  • - Head: 29.0 long blue cap, Ø11.0 through hole, 5.0 end bridge

  • - Inlaid stripes: 2 per stake, 2.0 wide × 72.0 long × 0.8 deep

  • - Puller: 93.5 × 100.0 × 9.0 (handle 24.0 grip, 9.0 thick; hook 7.0 thick, throat 13.0)

  • - Whole set on one plate: 180.0 × 236.0 × 10.0 (fits Bambu Lab H2D, X1/P1 and other 256 mm beds)

  • Print settings (Bambu Lab H2D, dual nozzle)

  • - 0.20 mm layer height, Bambu PLA Basic profile, 2 walls / 15% infill: 2h41m, 79.64 g (sand 56.49 g + blue 23.15 g), sliced in Bambu Studio 2.08

  • - Stronger version, 4 walls / 40% infill: 3h22m, 112.21 g (sand 78.18 g + blue 34.03 g)

  • - Filament 1 (body) desert sand #C9A66B; filament 2 (accent) alpine blue #2B6CB0

  • - Flat side down, no supports, no brim needed on a clean plate

  • - For real outdoor use, print in PETG or ASA (PLA softens in hot sun) and use 4+ walls.

  • Notes

  • - Original design. It has not been print-tested or load-tested, so the holding power hasn't been verified. Plastic stakes are for soft soil, sand, grass and snow. Don't hammer them into rocky ground.

  • - Product images are 3D renders. The lifestyle image, if included, is an AI rendering.

  • - Files: body.stl + accent.stl (whole plate, two colors), stake_*.stl / puller_*.stl (single parts), tent_stakes.3mf (sliced project).

Tagi