1 / 7
3D Printed Case for a Handwired Gherkin 30% Keyboard — zdjęcie 1
1 / 7

3D Printed Case for a Handwired Gherkin 30% Keyboard

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

An Ultra-Slim 3D printed case for the Gherkin 30% keyboard by 40percent.club

Ocena
0 / 5
Polubienia
2
Pobrania
0
Wydruki
0
Wyświetlenia
12
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

To build this model, you will need

  • A soldering iron, flux, and solder

  • Copper wire (I recommend ~16-18 AWG. I tried using 10 AWG to give the board more heft, but it was a bit too cramped in such a small case)

  • Insulated signal wire (I recommend using the individual wires from ethernet cables)

  • Heat-shrink tubing or electrical tape

  • Double-sided tape

  • One: Adafruit KB2040

  • One: Gherkin_Plate

  • One: Gherkin_Case

  • Two: M2x6mm brass standoffs

  • Four: M2x4 screws

  • Four: Rubber feet (optional)

  • Thirty: 1N4148 fast switching diodes

  • Thirty: MX-compatible key switches

  • Thirty: Compatible keycaps of your choice

Both models can be printed with standard settings on a 0.4mm nozzle, but I recommend printing them both at 100% infill for greater rigidity and weight in the hand. 

For more information on how to hand wire diodes and rows, watch Joe Scotto's video on how to wire columns, rows, diodes, and where to apply heat shrink/electrical tape (Up until 12:28).

Insert two of the M2 screws from the top of the Gherkin_Plate and thread on the M2 brass inserts. Then, insert your key switches of choice into the Key_Plate and solder the diodes and row wires as shown in the wiring diagram (the wiring diagram represents a top-down view of the keyboard from the side of the keycaps, so the diagram maps exactly to the image showing the keymap). Note that because of how the rows are set up in the firmware, one row could be lengths of six switches connected by one wire, or two separate lengths of wire split up into four and two switches. To connect these split rows, you will need to solder them together with insulated wire (for this I recommend using the brown/orange wires from the ethernet cable). 

Wire the row and column controller wires to the KB2040 according to the second wiring diagram while the KB2040 is taped to the slot in the Gherkin_Case, leaving enough slack in the wires to have the keyboard open while you work on it but not too much that you can't fit it all within the case.

Once you are done wiring, don't close the keyboard! Plug it in while holding down the BOOT button to enter the bootloader, and drag and drop the .uf2 firmware onto the drive that pops up. Test out all of the switches using the keyboard tester in QMK Configurator. If it works, then you're done! Close up the keyboard, put your keycaps in, and stick on some rubber feet if you like.

If the keyboard doesn't work, some common issues are:

  • Column/row wires shorting against each other because the heat-shrink/electrical tape melted through

  • Faulty switches (you can test this by putting the two probes of a multimeter set to continuity detection on each prong of the switch and pressing the switch down to see if the internal contacts are making an electrical connection)

  • Bad signal wire solder joints (an entire column/row will not work if your signal wire is not soldered well to the copper columns/rows or the pads of the KB2040

  • Individual keys not working due to bad solder joints on the prongs

Tagi