1 / 4
NSPanel Pro 120 – 8° Tilt Adapter for EU/PT Wall Boxes (Self-Tapping Screws) — zdjęcie 1
1 / 4

NSPanel Pro 120 – 8° Tilt Adapter for EU/PT Wall Boxes (Self-Tapping Screws)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Tilts the NSPanel Pro 120 up 8° and mounts it on EU/PT 60 mm wall boxes. Slim, OEM look, no supports, tested fit.

Ocena
0 / 5
Polubienia
1
Pobrania
1
Wydruki
0
Wyświetlenia
7
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

SONOFF NSPanel Pro 120 – 8° Tilt Adapter for EU/PT Wall Boxes

The NSPanel Pro 120 is made for US wall boxes, so it doesn’t fit European round boxes. It also sits a bit low to read comfortably at normal switch height. This adapter fixes both: it mounts the panel on a standard EU round box (60 mm screw spacing) and tilts the screen 8° upward, toward your eyes.

I wanted it to look like an accessory you could buy from SONOFF, not a printed bracket. The adapter matches the panel’s outline exactly, and its sides step slightly inward toward the wall, so the panel looks like it floats.

Tested and fitted on a real NSPanel Pro 120.

Features

  • Fits EU/PT round wall boxes with 60 mm screw spacing (Portugal, Spain, France, Germany and others)

  • Curved slots for the box screws that work with horizontal or vertical screw positions and allow ±14° of rotation, so a crooked box isn’t a problem

  • 8° upward tilt, 4 mm thick at the top and about 21 mm at the bottom

  • Same outline as the panel (74.5 × 122.5 mm) with softened edges

  • Locating lip and two pins that align the NSPanel base exactly. The base presses into the lip snugly even before you screw it.

  • Screws straight into the plastic. No heat-set inserts needed.

  • Prints without supports

What you need

  • 2× 3.0 × 8 mm self-tapping screws for plastic, pan or wafer head. Don’t go longer, because the top hole goes all the way through.

  • The two existing M3.5 screws from your wall box

  • Do not use the US 6-32 screws that come with the NSPanel. They’re too wide for the pilot holes.

Print settings

  • Material: PETG or ASA. Avoid PLA, because the panel gets warm and the adapter sits on a mains box.

  • Orientation: wall side down, as exported

  • Layer height: 0.2 mm

  • Walls: 3

  • Top/bottom layers: 5

  • Infill: 15–20% gyroid

  • Supports: none

Installation

  1. Turn off the power at the breaker.

  2. Pass the wires through the centre opening.

  3. Screw the adapter to the wall box with the box screws, through the slots.

  4. Wire the NSPanel base.

  5. Press the base into the adapter’s lip and fix it with the two 3 × 8 mm screws.

  6. Click the screen onto the base.

Notes

  • The base holds in the lip by friction alone, but use the screws. Friction can loosen as the plastic warms up, and pulling the screen off to service it tugs on the base.

  • Mains wiring should be done by someone qualified, following local regulations.

License: CC BY-NC-SA 4.0

Tagi