Ruckus ICX 7150-C12P Rack Ears & Printable M4 Shoulder Screws
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Stiffened 19" 1U rack ears for the Ruckus ICX 7150-C12P, with printable M4 shoulder screws. ZERO supports.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 9
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution
Stiffened 19" rack ears for the compact Ruckus ICX 7150-C12P (269 x 213 x 43.4 mm), plus printable M4 shoulder screws with a 6 mm hex socket. Everything stays inside the switch's own 1U. Nothing pokes into the rack space above or below. Teardrop-shaped holes where it matters, so everything prints with ZERO supports.
What's included
All-in-one 3MF: Plate 1 = left + right ear, Plate 2 = 8 x M4 shoulder screws (6 needed + 2 spares)
Ears only 3MF
M4 screws x8 3MF
M4 TEST screw x1 3MF (print this first)
HOW TO .txt with full print, mount and fix-it steps
All files are Bambu Studio projects for the P2S with a 0.4 mm nozzle and PETG, settings already set. Open, check the filament slot, slice, print.
Why 8 screws? Each ear takes 3, so you only need 6. The 2 extras are spares in case a thread prints rough or a socket gets chewed up. Printing all 8 on one plate also gives each screw more time to cool between layers, so the threads come out cleaner.
Print settings
Ears (Plate 1)
PETG, 0.4 mm nozzle
0.2 mm layers, 4 walls, 30% infill
Print as loaded: flat front plate on the bed
No supports. Nothing overhangs (even the screw holes are teardrops)
Screws (Plate 2)
PETG, 0.4 mm nozzle
0.08 mm layers (fine threads need it), 100% infill, 3 walls
Outer wall slowed to 40 mm/s
Print head-down as loaded, no supports
Tip: print ONE test screw first and hand-thread it into the switch before printing the set. Every printer's PETG is a little different.
What you need
6 mm Allen (hex) key
4 rack screws + cage nuts for your rack (ear slots are 9 x 7 mm)
Assembly
Hold an ear against the switch side, front plate flush with the switch front.
Drop a screw into each of the 3 tunnels. The round head fills the tunnel.
Push the 6 mm key all the way in, then tighten to snug. Don't crank it, it's PETG.
Repeat on the other side, slide into the rack, bolt the ears to the rails.
Design notes
16 mm solid spine behind the front plate: roughly 50x stiffer against twist than a flat 4 mm plate (section math, not a lab test)
8 mm of plastic around every switch screw
Screw: 12.6 mm head, 5.5 mm solid shoulder through the ear, M4 x 0.7 thread printed at 3.90 mm, 4.7 mm of thread into the switch (same depth as the factory screws, so don't use longer screws)
The shoulder stops 0.26 mm short of the switch, so the head clamps the ear tight
Troubleshooting
Screw binds in the switch: the thread is printing fat. Set X-Y contour compensation to -0.05 mm on the screw plate.
Allen key loose in the socket: your printer runs holes large. It'll still drive, just seat the key fully.
Socket rounds out: usually the thread is binding. Fix that first.
Fit tested in CAD: ears, screws and switch with zero overlap.