1 / 13
Cat Castle – Modular Gothic Cat House (bolted) — zdjęcie 1
1 / 13

Cat Castle – Modular Gothic Cat House (bolted)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Gothic castle chapel cat cave, 48×38×35 cm, 29 parts for 256 mm printers, bolted with cat-safe hardware.

Ocena
0 / 5
Polubienia
7
Pobrania
15
Wydruki
0
Wyświetlenia
52
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Pets
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

🏰 Cat Castle – modular cat house

Give your cat its own castle! A castle chapel as a cozy cat cave: pointed-arch portal with stepped frame, recessed lancet windows, rose windows in both gables, ashlar masonry, a slate-shingle gabled roof with a flattened ridge and four tall corner towers with crenellated crowns. 29 parts – every part fits a 256 × 256 × 256 mm printer – fully bolted with cat-safe hardware.

Features

  • Outer size 48 × 38 cm, ridge height 35 cm, towers 40.6 cm

  • Interior approx. 43 × 33 cm, 22–33 cm high – also for big cats

  • Entrance 14 × 16.5 cm

  • Cat-safe: button head screws + domed acorn nuts, no exposed threads or tips, all edges rounded, gaps below 1 mm

  • Removable roof for easy cleaning

  • Stackable tower extensions, prepared M6 pattern under every tower for future stilt modules

  • All files pre-oriented – no supports needed

Parts list (29 parts, approx. 5.9 kg filament)

Hardware

  • 74× button head screw M6 × 16 (ISO 7380)

  • 74× acorn nut M6 (DIN 1587)

  • 32× heat-set insert M6 (hole Ø 8.0 mm, length ≤ 14 mm)

  • 16× button head screw M6 × 20 and 16× M6 × 12 (ISO 7380)

  • Tools: 4 mm hex key (≥ 11 cm long), 10 mm wrench, soldering iron for the inserts

Print settings

  • PETG recommended (PLA possible, but not in direct sun / near a radiator)

  • 0.2–0.24 mm layers, 2–3 walls, 10–15 % infill

  • Walls & gables: masonry side on the bed (optional supports “on build plate only” for the window niches)

  • Towers: upright, 5–8 mm brim · Roof parts: standing on the centre seam, 8–10 mm brim, reduced speed

  • Floor plates & bars: top side down

  • Colour suggestion: light stone grey (walls, towers, crowns) + anthracite (roof)

Assembly

Step 1 – Floor: long bar in the centre (front to back), short bars crosswise left and right, counterbores down. Floor plates ribs down: A front left + back right, B front right + back left. Screw from below, acorn nut on top.

Step 2 – Front wall & front towers: the front wall flange slides under the floor plates. Tower R right, tower L left – the tower tab lies on the inside of the wall. 3 screws per side: head inside, acorn nut outside in the counterbore.

Step 3 – Side walls, rear towers, back wall: R at the back left, L at the back right. Bolt every overlap and all flanges.

Step 4 – Gables: rose window facing out, gable tab inside the side wall, 3 screws each.

Step 5 – Tower extensions & crowns: extension with 4 × M6×20 through the shafts, crown with 4 × M6×12 into the inserts.

Step 6 – Roof: A front right + back left, B front left + back right; 3 screws per side at the centre seam and at the ridge.

Step 7 – Place the roof: lower it in one piece – the lips hold it in place. Lift off for cleaning.

The complete guide with all details is attached as PDF (English + German).

Note: photos marked as visualizations are AI-generated based on the 3D model; the other images are renders of the actual model. Real print photos will follow.


🇩🇪 Katzenburg – modulares gotisches Katzenhaus

Eine gotische Burgkapelle als gemütliche Katzenhöhle: Spitzbogenportal, angedeutete Lanzettfenster, Fensterrosen in den Giebeln, Quadermauerwerk, Satteldach mit Schieferdeckung und abgeflachtem First sowie vier hohe Ecktürme mit Zinnenkronen. 29 Teile, jedes passt auf einen 256-mm-Drucker, katzensicher verschraubt.

  • Außenmaß 48 × 38 cm, Firsthöhe 35 cm, Türme 40,6 cm · Innenraum ca. 43 × 33 cm · Eingang 14 × 16,5 cm

  • Linsenkopfschrauben mit Hutmuttern – keine freien Gewinde oder Spitzen, alle Kanten verrundet

  • Abnehmbares Dach, stapelbare Turmaufsätze, vorbereitet für Stelzen-Module

  • Material: 74× Linsenkopf M6×16, 74× Hutmutter M6, 32× Einschmelzmutter M6, 16× M6×20, 16× M6×12

  • Druck: PETG, 0,2–0,24 mm, 10–15 % Infill; alle Dateien druckfertig ausgerichtet, ca. 5,9 kg Filament

Die komplette bebilderte Bau- und Druckanleitung liegt als PDF auf Deutsch bei.

Tagi