Cat Castle – Modular Gothic Cat House (bolted)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Gothic castle chapel cat cave, 48×38×35 cm, 29 parts for 256 mm printers, bolted with cat-safe hardware.
- Rating
- 0 / 5
- Likes
- 7
- Downloads
- 15
- Makes
- 0
- Views
- 52
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Pets
- License
- Creative Commons — Attribution — Noncommercial — NoDerivatives
🏰 Cat Castle – modular cat house
Give your cat its own castle! A castle chapel as a cozy cat cave: pointed-arch portal with stepped frame, recessed lancet windows, rose windows in both gables, ashlar masonry, a slate-shingle gabled roof with a flattened ridge and four tall corner towers with crenellated crowns. 29 parts – every part fits a 256 × 256 × 256 mm printer – fully bolted with cat-safe hardware.

Features
Outer size 48 × 38 cm, ridge height 35 cm, towers 40.6 cm
Interior approx. 43 × 33 cm, 22–33 cm high – also for big cats
Entrance 14 × 16.5 cm
Cat-safe: button head screws + domed acorn nuts, no exposed threads or tips, all edges rounded, gaps below 1 mm
Removable roof for easy cleaning
Stackable tower extensions, prepared M6 pattern under every tower for future stilt modules
All files pre-oriented – no supports needed
Parts list (29 parts, approx. 5.9 kg filament)

Hardware
74× button head screw M6 × 16 (ISO 7380)
74× acorn nut M6 (DIN 1587)
32× heat-set insert M6 (hole Ø 8.0 mm, length ≤ 14 mm)
16× button head screw M6 × 20 and 16× M6 × 12 (ISO 7380)
Tools: 4 mm hex key (≥ 11 cm long), 10 mm wrench, soldering iron for the inserts

Print settings
PETG recommended (PLA possible, but not in direct sun / near a radiator)
0.2–0.24 mm layers, 2–3 walls, 10–15 % infill
Walls & gables: masonry side on the bed (optional supports “on build plate only” for the window niches)
Towers: upright, 5–8 mm brim · Roof parts: standing on the centre seam, 8–10 mm brim, reduced speed
Floor plates & bars: top side down
Colour suggestion: light stone grey (walls, towers, crowns) + anthracite (roof)
Assembly
Step 1 – Floor: long bar in the centre (front to back), short bars crosswise left and right, counterbores down. Floor plates ribs down: A front left + back right, B front right + back left. Screw from below, acorn nut on top.

Step 2 – Front wall & front towers: the front wall flange slides under the floor plates. Tower R right, tower L left – the tower tab lies on the inside of the wall. 3 screws per side: head inside, acorn nut outside in the counterbore.

Step 3 – Side walls, rear towers, back wall: R at the back left, L at the back right. Bolt every overlap and all flanges.

Step 4 – Gables: rose window facing out, gable tab inside the side wall, 3 screws each.

Step 5 – Tower extensions & crowns: extension with 4 × M6×20 through the shafts, crown with 4 × M6×12 into the inserts.

Step 6 – Roof: A front right + back left, B front left + back right; 3 screws per side at the centre seam and at the ridge.

Step 7 – Place the roof: lower it in one piece – the lips hold it in place. Lift off for cleaning.

The complete guide with all details is attached as PDF (English + German).
Note: photos marked as visualizations are AI-generated based on the 3D model; the other images are renders of the actual model. Real print photos will follow.
🇩🇪 Katzenburg – modulares gotisches Katzenhaus
Eine gotische Burgkapelle als gemütliche Katzenhöhle: Spitzbogenportal, angedeutete Lanzettfenster, Fensterrosen in den Giebeln, Quadermauerwerk, Satteldach mit Schieferdeckung und abgeflachtem First sowie vier hohe Ecktürme mit Zinnenkronen. 29 Teile, jedes passt auf einen 256-mm-Drucker, katzensicher verschraubt.
Außenmaß 48 × 38 cm, Firsthöhe 35 cm, Türme 40,6 cm · Innenraum ca. 43 × 33 cm · Eingang 14 × 16,5 cm
Linsenkopfschrauben mit Hutmuttern – keine freien Gewinde oder Spitzen, alle Kanten verrundet
Abnehmbares Dach, stapelbare Turmaufsätze, vorbereitet für Stelzen-Module
Material: 74× Linsenkopf M6×16, 74× Hutmutter M6, 32× Einschmelzmutter M6, 16× M6×20, 16× M6×12
Druck: PETG, 0,2–0,24 mm, 10–15 % Infill; alle Dateien druckfertig ausgerichtet, ca. 5,9 kg Filament
Die komplette bebilderte Bau- und Druckanleitung liegt als PDF auf Deutsch bei.