1 / 20
Rackmount GL.iNet Comet X (GL-RM4PE) and ZyXEL GS1920-8HP Brackets — zdjęcie 1
1 / 20

Rackmount GL.iNet Comet X (GL-RM4PE) and ZyXEL GS1920-8HP Brackets

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Mount the GL.iNet Comet X (GL-RM4PE) 4-Port network KVM and a ZyXEL GS1920-8HP Switch side-by-side in 1U.

Ocena
0 / 5
Polubienia
1
Pobrania
0
Wydruki
0
Wyświetlenia
7
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
GNU General Public License v2.0

Mount your network KVM next to a small switch within the same 1U.

These parts allow you to mount these specific devices next to each other in 1U saving vertical space in your 19″ rack.

You may need to adjust these websites to your region.

The set consists of 3 separate parts:

The rackmount ear to mount the KVM to the vertical rack rails.

Main features

  • easy print without supports

  • securely attaches KVM and Switch together

  • Same parts allow for left and right side mounting of the KVM/Switch

Additions mounting material needed

  • 6 × M3 Counter sunk screws

The two-part interface plate that connects the two devices together so they form a mechanically stable-ish unit.

Once each of them is screwed into the devices they slide together front-to-back with a dovetail connection.

Looks like this. (Switch omitted in the picture for clarity.)

Mounting Material

You need 6 countersunk M3 × 6mm screws. 3 pieces on each side of the KVM. (8mm long screws are already too long and won't clear.)

You can use the black countersunk screws that came with the ZyXEL Switch for mounting the interfaceplate part (and the original metal rack ear) on the other side.

The countersunk screws are needed for mounting the printed brackets to the KVM. You cannot use the buttonhead screws that came with it, because they'll run into the vertical rails and make the whole device-combo just a tad too wide to fit.

The countersunk screws just barely clear when sliding the two device into the rack together.

Mounting the printed rack-ear to the KVM. Make sure the screws are sunk all the way in.

The metal ears that come with the KVM are too long, that's why I had to create this one.

Human made OpenSCAD parametric design.

Slides in Průša Slicer 2. Yes, I did print it like that without a brim, and that actually did work. If you run into bed-adhesion problems, add a generous brim to make sure it sticks.

The surface area on the build plate is really tiny. It worked on my machine! May or not stock on your printer!

The double winged part goes onto the KVM.

Once the 3 screw holes line up with the holes on the devices, the orientation certainly is correct. You cannot mount it the wrong way round.

Make sure the screw in the slideway is completely screwed in! If it's not, the other part will lock up on it.

You can test this, before screwing the other interface part onto the switch. If it slides in easily, without locking at the screw, you're good. Two color-scheme used to better visibility how the parts fit together.

This part goes onto the Switch. The outermost 4 holes are for the countersunk screws. The smaller 4 outer holes help aligning the plate onto the switch, just like the metal rack-ears that come with the switch. The two large holes go to the front of the switch.

I used my own M3 × 6mm countersunk screws, but the original ZyXEL ones work just as well here.

Now, slide the dovetail together. This is a tight fit by design.

The two devices joined together.

To slide in the whole assembly into the rack, you need to move completely straight from the front to the back. If you're at an angle it's likely that you cannot get the assembly in.

The mounted assembly of both devices next to each other.

Recommended Print Settings

This is an easy print, under an hour.

Slightly modify the 0.20mm STRUCTURAL preset.

  • PCTG or PET-G recommended. (No CF, GF variants needed) PLA will creep away over time.

  • 0.2mm layer height is fine

  • Increase the amount of perimeters to 5!

    • This makes the rack-ear essentially solid

    • Implicitly reinforces all the screw holes for save mounting

  • No supports needed, all screw holes can be bridged

A preconfigured .3mf project file is provided with a sequential print.

The rack-ear goes first, so you can cancel the print without any risk should it come loose too early.

Left or right side mounting

The parts are left-right compatible, so if you prefer the KVM on the other side, there's no need to reprint. Even if you decide to switch them around later.

ZyXEL Networks Switch compatibility

I've used this with my GS1920-8HP, but from my experience with ZyXEL switches I assume the same interface plate should work with other like-generation 10″ switch models.

Switch Ventilation

Some ZyXEL switches have a side-to-back airflow. This interface-plate leaves enough room to the side of the switch, so it can pull in air without obstruction.

Post a Make!

Show us your 19″ rack mounted devices! Also please mention your specific switch model, so others can learn which models are fully compatible!

Check out my other Models!

Some are oddly specific, but each one is caringly made by a human, without any shitty AI. All of my models are provided as clean, well-tested, and verified printable geometries.

Version history
  • 2026-11-14 initial publication

Tagi