1 / 1
Oculus Rift S Headstrap Ratchet Retention Gear Upgrade / Replacement — zdjęcie 1

Oculus Rift S Headstrap Ratchet Retention Gear Upgrade / Replacement

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This is a upgraded Oculus/Meta Rift S head-strap ratchet mechanism built for longevity and a more sturdy click and fit.

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
1
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

This is a upgraded Oculus/Meta Rift S head-strap ratchet mechanism built for longevity and a more sturdy click and fit.

INSTALLATION:

  1. Take the facial interface off of the Rift S

  2. Unplug the headset strap audio connector and switch the strap lock to off

  3. Hold the adjustment button and slide the strap off

  4. Take the foam off the back of the headstrap (It has internal plastic clips that just pop off, non-destructively) start from one side and work your way to the other

  5. In the center of the back of the headset strap where you just pulled the foam off you'll see a 3 pronged holder clip mechanism, push one or more of the clips in and pull/wiggle the knob on the back of the strap

  6. Once the knob comes off you'll see the OEM gear part we need to replace. The hardest part of the whole process is pinching all 3 clips in to slide the OEM gear off.

  7. Once you have the OEM gear off slide my part into either the headset strap itself then put the knob back on or put it on the knob first. Whichever you find is easier. WARNING: the strap can become uneven in this process so I like to pull the strap all the way back, insert the gear partially (it cant be inserted entirely because of the internal end stops on the rails) and then push the strap slightly forward as you apply light pressure to the gear to ensure it inserts at the first top teeth... or make sure it's relatively evenly lined up if you don't care for perfect.

  8. Then you can snap the knob back on and snap the foam liner & facial interface back on

  9. Enjoy! The head-strap ratchet should work and hold tighter than stock now and hopefully not degrade over usage.

PRINTING:

I only tested printing it at 0.10mm and 0.15mm I'm unsure if it works at any other values. Your mileage may vary.

HISTORY:

The Oculus Rift S head-strap ratchet mechanism was designed terribly. It uses plastic instead of springs to hold tension. They also use terribly thin plastic making it unnecessarily susceptible to bending in exchange for slightly more silent operation. Over time it is essentially inevitable that the OEM part will end up too deformed to ratchet at all allowing the strap to slide freely.

Many people use high density foam (from this Reddit thread) as a hack fix for this, and who can blame them.

I personally resell and refurbish these headsets so I wanted a more permanent solution. Luckily on the same thread and also with some searching a 3D printable solution was findable, with a number of caveats.

My design was made using this as a reference, I wouldn't have been able to do it without it. However it still had it's issues of course.

  • The thickness and stiffness of the part still led to the same degradation over time

  • The square cutouts on the arms weren't perfectly square leading to slipping

  • One of the arms was misaligned slightly leading to only two of the arms making full consistent contact

Which leads my to my design. My design fixed those two big issues.

  • It uses thicker arms on all versions for longevity and stability while maintaining ease of adjustment.

  • The interior of the square cutouts for the arms don't have any rounding and fit perfectly inside of the headset strap internal gear

  • All arms are perfectly aligned

I made 3 variants, Strong Medium and Light. Each makes a louder click then the last and is more sturdy then the last. Medium is the one I ship in all of my refurbished headsets and it feels better to me than the OEM part. 

Tagi