274 modeli
I stopped uploading and updating my models here at Printables! My actual models can be found on my MakerWorld profile – with print profiles. Take care to use the newest models … Similar to GekoPrime's Clip for the other places. But this…
Untested work in progress
This safety eyes need to be printed with low layer height (0.1mm) to achieve a nice result. The eyes are made from two different parts for ease of printing (the rod and the head) that need to be glued together, and also it make it easy to…
A parametric case for standard 1/4″ hex bits , designed for practicality and flexibility. The main case is print-in-place and uses 4 mm DIA × 1.5 mm or 3 mm thick magnets to keep it securely closed. The spring tabs in each row hold the…
This is a remix if the inner portion of my original model. This one is intended to be printed with rigid filament (PLA, PETG, ABS, etc.). It has the corresponding number of holes on the bottom to insert 6x3mm magnets for bit retention.…
Every time I loosen up the two Idler tension screws and open the MMU2s one or both of the screws and their springs would fall out. They would bounce around and play a mean game of hide and seek. So I made these little guys. Literally the…
Hook part extended by 5mm on both mounts. Category: Computer
This a replacement for a common part that fails in most socket AM2 AM2+ AM3 AM3+ FM1 FM2 machines. I have only used it my AM2+ machine. I would recommend that you print it in a vertical orientation with walls set to 99 and infill set to…
Uses 4 M3x15mm bolts 4 M3 nuts 4 M3 washers (optional) The backplate has a second version which doesn't require supports and will bridge the overhang instead Consider rotating the retention mount for better strength. That will instead…
Remix is the head (8mm) and rod piece together as one piece. No glue required.
Printed with no supports, .2 layer height, 4 top and bottom layers, 3 side layers, 40% infill.
Key Features of the Door Seal Add Heat Retention: Our door seal brings the heat, literally. It's all about insulation, creating a stable printing zone that spells primo print quality. Reduce Drafts: Reduce unwanted temperature shifts, the…
Quick printed version of the kydex AR mag inserts you'll find in nicer pouches. If printed in PLA they will creep over time, but I've found the retention to still be pretty reliable over time. Obviously higher temp resistance materials…
Print instructions: 0.2mm layer height 4 walls for strength 100% sparse infill Turn off single layer for Top Surfaces
Many printers, especially those with a Bowden extruder, use PC4-M10 fittings to retain the PTFE tube at the extruder. Reportedly on Bowden printers it helps with retraction if the fittings at both ends have a firm grip on the PTFE tube so…
Gridfinity holder for socket/female side of USB A devices. I use mine to hold USB A to USB C adapters. If desired, there is also a looser fit model. The base model is a friction fit that acts a pseudo handle. Printed with PLA+ (regular…
This .scad will generate a ball bearing retention ring of any size you want with any number of balls! I created it to work with Airsoft pellets (BBs) but it will work with any ball or sphere shaped object. The idea is to use this in a…
This is a remix of fellow Phil's excellent Pastamatic retention pin available here: https://www.printables.com/model/100. , to combine with the original Pastamatic, available here:…
Pastamatic Filament Spool Winder Add-On by Kistek. This add-on is for Pastamatic filament spool winders and is meant to secure the drive spindle so that it does not come out of the cradle during operation. This is especially important for…
Are you ready to experience the next level of gaming convenience? Introducing the phenomenal Wall Mount Bracket Remix for the Nintendo Switch! Brace yourself for a description that will make your heart race, your palms sweat, and your…
A simple Flag pole holder. Anchor/bolt spacing based off standard brick joints and using 3/16" bolts. Sized for a 1" flag pole. Infill: 20-30% Infill Modifiers: 99-100% as shown in photo Support: Yes, Tree Walls: 4-6 Top/Bottom Surfaces:…
Retaining clip for DieselGeek's amazing first gear getter bushing. Under heavy use, the bushing may fall out due to its friction fit. This 3D printed plastic clip slides over the bushing and holds everything securely in place. You can…
Cable Retention Bushing / Gland for USB cables, for example from arcade sets from Aliexpress. Lock tab is 8 x 8.5 x 1.6 mm. Cable is 4 mm. For holes 18 mm or 22 mm. I printed a layer of 0.16 mm.
The Impulse Ungineering Ontos O-ring Breech is a modified breech part that uses a DASH-016 O-ring to assist with barrel retention. The O-ring adds extra friction where excess vibration from play may push the barrel out of the blaster.…
This is a box for up to 3 sd cards, that is made to be durable, with spring loaded retention brackets to make sure the SD cards don't fall out. There are two versions, either a print in place one, or one using a 12mm M3 bolt and nut. The…
While using the original model, the parts always fell apart when my cables would move slightly, so I designed this little press-fitted cap to fix this problem. The whole inner assembly could still leave the outer ring at that point, so a…
*** Thanks for checking out this model! *** If you appreciate what I'm doing, please consider buying me a coffee , and check out my other models ! ********** I've tried a few of the bit holsters out there but none seem to have worked for…
Replaces the spring and blade retention pin with a self retaining spring and a larger base pin, also adds one more locking lobe so the spring doesn't get squished. Print Settings: Layer Height: 0.2mm Infill: 30% Material: PETG Supports on…
Prevent your Powerpole connectors from accidentally separating. The clip fits into the existing retention holes with a slip friction fit. Still removable by fingers thanks to a ridge on the clip, but will stay under vibration and normal…
An upgraded go-pro compatible holder for the UV5R radios. There is an added slot for better belt clip retention to help prevent movement under off-roading conditions. It also significantly helps reduce noise from the radio rattling around…
This is a retention sheath for a full sized Kabar (1211 in my case). The sheath has two lugs that bend downward when inserting the knife into the sheath and spring up behind the cross guard, retaining the knife in the sheath. To remove…
The retention clips are quick and easy to use, except a bit fiddly to open. Added finger tabs to make it easier to manipulate. Remixed both the normal retention clips, and the larger one that is for the drive side on the receiver spindle
Redesigned from scratch for the OLED variant's dimensions and features such as speaker ports and vents. Added retention clips to hold the device in the mount for added safety. Retained the original aesthetic although slightly modified,…
This is a replacement nut used to clamp the shade in place on my lamp's light socket. The factory's original part broke due to heat fatigue. I printed this model on my Prusa MK3S+ using polymaker's "Galaxy Black" 1.75mm PolyLite™ PLA…
This is a remix, adjusted and optimized for TetherPRO cable and Nikon Z6 Mark II
Tired of cutting yourself on your chisel when you dig for something in your toolbag? Or sick of finding out that the chisel you just sharpened has been dinged by another tool in the drawer? Fear no more, these guards are easy to print,…
This is a snap down retention bracket for hard drives and SSDs in MODE. Normally a SATA drive is secured down to MODE with 2 screws through the bottom. However that means you need to remove MODE from the console to get to the bottom of…
The original shaft had a tendency to slide off the side supports during use, so I extended it by 2–3 mm and added holes sized for an R-clamp to keep it securely in place. Printed successfully in both PLA and PETG without issues. For…
Print 100% infill. I've used PETG because it need to be flexible. Mount between the adapter and the spool winder as you can see in the image
I found the original version very good and useful, however I usually squash the first layer so the part came out rather sharp on the edges, this remixed version have a chamfer for softer grip. Also, I didn't want to glue the socket…
Remixed the strongest pegboard clip I've seen to make it a bit more sturdy and added removal openings
Concept 2 rower phone or device rest/mount remix of model from Leoquart
A quick remix of figterk's excellent bit holder for the LTT screwdriver. This is the 60-bit insert, split into 5 pieces. This is a split version of the 60-bit insert, enabling users to easily print in multiple different colors for each…
This is a remix of the original to address a few issues I had: Cover was sliding off the back on some long prints due to vibrations Extruded the lip to match the front two pieces to fully retain the glass top PTFE guide was allowing too…
Got tired of the Velcro pads failing constantly, forcing me to adjust the floor mats every damn time I got in the car. This is my solution. Printing: Small part, so go 100% infill @ .2 or smaller Button face down Organic supports on…
Full reduced friction feeding system For extruder number one on the Prusa XL from the left side mounted spool holder using an additional filament guide mounted using the same method as the OEM filament guides. The natural spring tension…
I have the same problem as most with the UV-5R. If you move the headset plug slightly, the radio will no longer work. There is already a solution for this here. However, I didn't like it because it is too bulky and you have to buy screws.…
I had mounted my Argon Neo on the side of my Lack Enclosure, but was having issues with the case falling out of the mount over time. I remixed the design to introduce a retention clip. I opted for an interchangeable clip to allow reuse of…
Requires 10-32 screws, 2.5" lg, qty 3
Filament Spool Holder Retention Clamp for Bambu Lab A1 to prevent the filament spool from slipping off the filament holder My print settings for PLA: 0,2mm layer height 5 walls only one wall on top and bottom layers 5 top and bottom shell…
AM4 Retention Bracket for a iCUE H150i ELITE CAPELLIX Liquid CPU Cooler. Corsair has a retention bracket for sell on its web site. It is currently not in stock. So I designed this bracket in blender. 6-32 3/4 Screws is what I used to…
I created this model to store the cable I use for hooking e-matches to my DIY electronic fireworks rig. Each currently has about 15m of bog standard speaker cable on in. The spools are easy to churn out and put together. They have a key…
Jack retention/support system nut for Dacia/Renault Dokker also known as Renault Kangoo in some markets. It's an original model very close to the original part. the center screw hole Isn't fully threaded, you can directly thread it on the…
For extra strength use 3 or more wall loops. Different models for more or less bit retention, retention weakens with use. (Its plastic what can you do?)
These TPU retention sliders hold hydrofoil T nuts in your desired position between sessions. They speed up assembly and disassembly before and after foiling sessions. They are easy to install, and slide to reposition with a hex or torx…
With my New direct drive Hot end cable management through the frame and out the back was not overly practical for taller prints so I made this bracket to retain the cables at the front over the X Axis end stop. Print Settings Printer…
Should be compatible with any Crosley Cruiser portable model. Printed in PLA with 0.1mm layer height, 2 perimeters, supports everywhere.
The original front/side panel retention clips on the Jonsbo D41 computer case are lousy and brittle. I decided to make these when I accidentally broke 3 of the original clips when attempting to put my side panels back on. I was able to…
Replacement panel retention clip for Silverstone Fortress tower cases such as FT03 and FT03-mini, may also work with other Silverstone cases. This is the small piece that screws into the side panels that allow it to clip into the case…
Tonneau cover strut retention is a small plastic clip that the cover strut snaps into during travel. REV01 added rib for increased strength. Tonneau cover is made by BAKFlip, model 448329;…
A very secure clip that holds cable along a piece of 2040 extrusion
A parametric set of organisers for standard 9.5 mm and 13 mm (Japan) driver bits—perfect for keeping your tools secure and tidy in a toolbag. Each slot uses spring-tab retention to hold the bit firmly in place so it won’t rattle loose or…
I lost my original stock bracket and cpu cover as I had used an aftermarket aluminium support bracket for better pressure distribution. As I wanted to store my motherboard in its box, I remixed this design to allow me to cover the socket…
No more wimpy pegboard retention clips. This one has some stout. It hold fast and you may even need a flat blade screw driver to remove it. Happy Printing! You can help To help cover the expenses of printing prototypes for the models I…
This is a mount for a Baofeng UV-82 with plug retention. The application is for a 24 Hours of Lemons car and mounts to a round dash bar, but there may be other applications so I uploaded it here. The clip around the side prevents the…
This is a remix of Mordiev's MMU2s Tension Screw Retention Washer designed for printers with .6mm nozzles. For whatever reason, the inner diameter (ID) of the original washer design was too big and kept falling off of the idler screw - I…
I made myself a sliding shelves, but Dewalt box slides on top of it. That's why I made this leg holder which holds ToughSystem box on it. There are two variants, hidden and with the lip. Lip version helps you to make box flush with the…
These are simple tabs meant to hold mirrors, boards, posters and the like to your wall. Both the depth and counterbore should be easy to edit in Fusion360 (or your program of choice) if you need different specifications. I suggest…
I designed this with a 370SP slocket and an ASUS P3B-F rev 1.04 motherboard. I assume it will work with other slotkets and motherboards. I used nylon fasteners to attach it to the motherboard, and M3 socket head screws to attach the cap.…
I have created a Model to print those fragile seatback retention clips in the trunk of the Ford III. I have printed them as rigidly as possible and used PETG for best layer adhesion. The support comes off quite easily, I'd however suggest…
The metal version works with precise 16 mm ball bearings. The glass version was made to work with slightly bigger glass marbles (d = 16.5-17 mm) The best stiffness of P1 is achieved with aligned rectilinear infill along the long axis.…
Credits to FreedomDuck. XT60s coming loose on GT's is a known issue, but you won't catch my face in the pavement because of it! Every picture I have seen of this happening was on the controller box. You can install the clip directly on…
MWS Nozzle Return-Spring Retention-Piece Pin Punch assist Block
This box has space for 2 handles and something like 40 #11 blades. The lid is held closed by small disc magnets and the blades are held in place by much stronger magnets below. There are three points during the print where you will want…
This is a remix of the original mmu2s selector from prusa. I always had problems with the reliability of the finda sensor in the selector. I first tried the mod with a magnet e.g.…
This is a Speed Wheel for a Panavise Jr. I recreated the wheel and added retention nubs to it. I found that the one sold by Panavise would occasionally fall off if you're spinning quickly. This one has a tight fit and won't come off until…
Remixed version of the awesome front center brace adapter by Miatafied. I added a slot to keep the end in the tube. I used M5 tee nuts that I had on hand. M5 bolt for the thumb screw. I also made an insert for the rear of the brace where…
I have a set of issue knee-pads that had one of the clips break on it. I wasn't able to find a replacement so I designed this replacement instead. Printed on a Bambu X1C in ASA on the side of the model (See slicer photo) with no other…
A retention clip for the Anderson Powerpole series 1327 housing (15-45 Amps), commonly used in FRC. There are locking pins that slide into the holes formed by 2 or more joined powerpole housings. Modeled by qwertpas. Print Settings…
This is TS-FT002 holder suitable for inside of the retention tank. I recommend ABS, supports required only on build plate. When you will put TS-FT002 inside retention tank, ensure you at least coat the PCB eg. with nail polish, eg. like…
The second iteration of my needle file holder. Based on a 9mm 50 Round Case by jamesbrogers on Thingiverse.
The Tidy Cats Breeze pellet litter boxes are great. What's not great is when you have an adorable cat that takes delight in playing with the pellets and kicking them out of the box. The XL box has a too-generous entry door that makes it…
Remix of FlyingPurpleCow's Trophy Base . This remix adds a 1mm cover over the faceplate opening , keeping the plate securely in place after insertion — no glue needed. All other parts (solid base, modular top/bottom, weight storage) are…
There are a couple remixes to insert a hygrometer into “enclosure cutout seal front”. But they rely on friction to remain in place in the enclosure wall, and I wasn't comfortable with that. I remixed “enclosure cutout seal rear” to hold…
Remix of the Voron Euclid dock by ProtaDec to give it another 2-4mm of length adjustment, and a hole for a 6mmx3mm magnet (friction fit). Their dock was really close to fitting on my setup, so I added some length to be safe. I found it…
This is a two piece, parametric MOLLE cylinder (smoke grenade, flashlight, bottle, etc.) pouch with elastic cord retention. While the exported models here fit Polish ED-60 and GD-10 smoke grenades, and a Olight Baton 3 flashlight, you…
I printed the original project and had the problem that my joycons kept sliding out of the chassis 😵 This modification adds a gap to the top of the rail (exactly like the switch has) so that the joycon retention clips actually secure…
Old Uncle Dogmoth has something special for you today: Two extended versions of the level 2 retention strap, 150mm and 155mm in length, along with the original length if you just need a replacement. I needed something a bit larger for my…
Just a simple remix of Bele2009's excellent mount that adds retention tabs to keep it from sliding out front to back when mounted in a different orientation.
Now the tensioning screws and springs don't fall out when you open the MMU and flip the top over. Print Instructions Start with PrusaSlicer's default PETG 0.2mm SPEED preset. Add Support Enforcers for the tabs sticking out.
This is the retaining clip for the rear drip moldings and replaces Mazda part number B092-50-525 which is NLA. I've tried printing this a few different ways, but FDM printing, even at a fine layer height just doesn't seem to get the…
This single-dose hopper system for Breville Express minimizes ground powder retention in the espresso machine, improving espresso quality. It eliminates a gap between the hopper and the exterior burr by making the tip of the hopper body…
Sleeve with retention to hold battery better than base version
Add-on retention clip secures the bac water to the clamp for non-shroud type spike valves. Original clamp: https://www.printables.com/model/1286014-bac-water-and-spike-support-clamp
I liked @ Kinematic Digit s version of the universal spool holder for Enders/Cr-10++, but I found it a bit fiddly to hold the two parts together when removing the “nut”, so I added some small holes that fit 8x3 disc magnets to keep them…
Braces longer cables at the back of an EBB36 tool head board installed on a Xol or similar
Important note: print the BCAR bodies muzzle-down! Much like my other BCARs, these all use F683ZZ (3mm x 7mm x 3mm) flanged bearings and 3x14mm dowel pins. These also use the same -016 O-ring as Sillybutts' MXL spigot scars (more info at…
In case of lost spring it is possible to use spring from clicker pen. Original pin securing the clip in place is required (or another solution). Some sanding might be required for ideal fit.
FR Tournevis compact avec chargeur 8 têtes à rétention magnétique. 1 aimant cylindrique de 1 cm x 1 cm est indispensable pour le fonctionnement du stockage intégré au manche l"aimant est en contacte avec la base de la lame porte tête ce…
Yet another thumb wheel for a M3 bolt. Category: 3D Printer Parts
