LiPo pack for GameBoy DMG-01
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Intended for resin printing. Additional supplies You'll need the following parts to complete assembly: TP4056 LiPo…
- Ocena
- 0 / 5
- Polubienia
- 12
- Pobrania
- 30
- Wydruki
- 0
- Wyświetlenia
- 544
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor Toys
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Intended for resin printing.
Additional supplies
You'll need the following parts to complete assembly:
- TP4056 LiPo BMS: https://smile.amazon.com/gp/product/B07T816M2X
- 103450 LiPo pack: https://www.aliexpress.com/item/1005001303560042.html
- Positive terminal: https://www.aliexpress.com/item/32949854416.html
- Negative terminal: https://www.aliexpress.com/item/4000953728880.html
- M2*6 screw: https://smile.amazon.com/Stainless-Phillips-Machine-Screws-100PCS/dp/B07HGNNCLV
- 1.5mm drill bit: https://smile.amazon.com/gp/product/B01DBN8PLI
- Wires: https://smile.amazon.com/gp/product/B01LH1G2IE
- Flux, solder, etc.
Assembly
- Print. The "45" files are in recommended print orientation.
- Finish printed parts. Remove supports, file excess, sand, etc.
- Use 1.5mm drill bit to ream the pilot hole for the positive terminal.
- Secure positive terminal with an M2, 6mm screw.
- Push negative terminal into position - it will lock itself in place.
- Solder LiPo "+" wire (red), and TP4056 "BAT+" terminal to the positive battery terminal.
- Solder LiPo "-" wire (black), and TP4056 "BAT-" terminal to the negative battery terminal.
- Isolate battery from contact with TP4056 using Kapton or other tape.
- Assemble pieces within "Body".
- Secure LiPo & TP4056 with small amount of hot glue.
- Reinforce wires with hot glue.
- Glue "Panel" in place.
- File/sand as necessary to fine-tune the fit with your GameBoy.
Technical notes
The original GameBoy ran on 4xAA batteries, so the nominal power input would have been 6V. A 103450 LiPo pack however, only provides 3.2V-4.3V, depending on how fully charged it is. This is not a problem for the GameBoy DMG-01, because it contains an internal voltage regulator, which converts arbitrary inputs (within reason) to 5V. I've tested & confirmed this with a DC Power Supply, and confirmed that the GameBoy runs fine on all voltages a LiPo may output. The screen cuts out under ~2.5V, but the BMS board on the LiPo pack shouldn't allow it to discharge past 3.2V, to protect the LiPo itself from damage. Further, the power (W) consumption of the GameBoy does not vary significantly from 3-7V
Print Settings
Printer Brand:
Anycubic
Printer:
Photon
Rafts:
Doesn't Matter
Supports:
Yes
Resolution:
0.05mm
Infill:
100
Filament: Elegoo Resin, water-washable Clear Blue
Category: Toy & Game Accessories