Hemera XS mount for E3D ToolChanger

2 different versions of the mount, unmirrored and mirrored. 

To save as much space as possible I moved the filament lever underneath the receiver, though it doesn't look like it, the filament lever is still quite easily accessible and if you use macro's for loading and unloading, you don't even need to use the lever.

Important note: you need to replace the tensioner with a M3x30 (M3x28 for the mirrored version) screw to use the mount. Use a screwdriver to adjust the tensioner, and with the mirrored version, you need to pull the filament lever to access the screw.

Screws needed

• Tool:
  Buttonhead or cylinderhead
  4x M2.5 x 6 or M2.5 x 8
  1x M3 x 30 or M3 x 28 (For the mirrored version or if you use a cylinderhead screw, you need a M3 x 28 screw (I just sawed off a m3x30 screw.))
  7x M3 x 8
  5x M3 x 6
  4x M3 x 20
  
  Countersunk
  6x M3 x 8
   
• Dock:
  Buttonhead or cylinderhead
  2x M3 x 10
  4x M3 x 16

Parts to print

• Unmirrored version
  
  Tool:
  TC-HEMERA-XS-V4-DOCK-BRACE
  TC-HEMERA-XS-V4-DOCK-BRACKET
  TC-HEMERA-XS-V4-PLATE-ADAPTER
  TC-HEMERA-XS-V4-RECEIVER-TOP
  TC-HEMERA-XS-REVO-PCF-DUCT or TC-HEMERA-XS-V6-PCF-DUCT
  
  https://github.com/e3donline/ToolChanger/tree/master/V6%20Tool/STLs
  V6 Cable Support.stl
  
  https://github.com/e3donline/ToolChanger/tree/master/Hemera%20Direct%20Tool/STLs
  Hemera_PCF_Bracket.stl
  
  Dock:
  TC-HEMERA-XS-V4-DOCK-ADAPTER
   
• Mirrored version
  
  Tool:
  TC-HEMERA-XS-V4M-DOCK-BRACE
  TC-HEMERA-XS-V4M-DOCK-BRACKET
  TC-HEMERA-XS-V4M-PLATE-ADAPTER
  TC-HEMERA-XS-REVO-M-PCF-DUCT or TC-HEMERA-XS-V6-M-PCF-DUCT
  
  https://github.com/e3donline/ToolChanger/tree/master/V6%20Tool/STLs
  V6 Cable Support.stl
  V6 Receiver Top.stl
  
  https://github.com/e3donline/ToolChanger/tree/master/Hemera%20Direct%20Tool/STLs
  Hemera_PCF_Bracket.stl (Mirror this in your slicer software)
  
  Dock:
  TC-HEMERA-XS-V4M-DOCK-ADAPTER
   
• Load filament macro
  Cut the filament at an angle, push it in until it hits the gears, heat up the hotend, pick up the tool and run the macro.

M83    ; Relative extrusion mode
G1 E60 F300  ; Extrude 60mm
 

• Unload filament macro
  Heat up the hotend, pick up the tool and run the macro.

M83    ; Relative extrusion mode
G1 E5 F5000  ; Extrude 5mm
G4 S1   ; Pause 1 second
G1 E-80 F500 ; Retract 80mm

Updates

Added PCF ducts for Hemera XS V6 and renamed Revo PCF ducts to TC-HEMERA-XS-REVO-PCF-DUCT and TC-HEMERA-XS-REVO-M-PCF-DUCT.