🧥 Parametric clothes hanger with folding hooks (multiple hooks on a rack possible)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
0,85 € – 1,04 € netto (bez VAT)
Dla pliku: hook_1.8_0.2mm_PLA_MK3S_1h11m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,95 € netto (środek widełek).
- Masa podana przez autora
- 7 g
- Czas druku podany przez autora
- 1,18 godz.
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Hanger for wall placement with folding hooks (no MMU needed) - parametric source. No supports.
- Ocena
- 5 / 5
- Polubienia
- 64
- Pobrania
- 205
- Wydruki
- 6
- Wyświetlenia
- 1172
- Oceny
- 4
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other House Equipment
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Info + features:
- parametric source file (so you can create any length with any amount of hooks that fit your printing plate)
- it is on purpose NOT print-in-place, so anyone can have colored hooks
- just pick a rack and print required number of hooks for it
- it is printed standing → allowing the front surface to be smooth
- invisible joint. Even when hook can be put on and off - from the front the joint is completly invisible, so it looks as in print-in-place solution
Print info:
- see 3mf if you can
- rack must be printed upside down!
- PLA
- no supports
- no brim (at least for clean plate surface), but use brim for textured plate.
- 0.2mm layers but recomending variable layer height for the hook (the higher the thinner layers, because hook is angled towards the top)
- infill: recommending at least 10-15% gyroid
- with reinforcements especially around:
- the joint (especially the part where hook is pressing up when wide opened)
- the hole for attachment to the wall
- consider higher % when planning to hang extra heavy objects
- with reinforcements especially around:
Parametric info:
- source file is in Blender, open it, between objects, click “RACK” and open properties (or hit “N”)
- params:
- hole_width: width of the hole for a hook in cm
- hook_count: number of hooks
- space_end: distance from one side end to the nearest hook
- space_middle: distance between hooks
- vertical_gap: gap between hook hole and hook
- y_thickness: thickness od the rack and hook (quite experimental, other than default value may work not that well)
I understand that not everybody is familiar with Blender, so if you were not able to modify params in Blender and export it to STL, just write me requirements.
Assembly:
- click the hook inside from the behind, little force is needed
- so it is positioned correctly in the joint and can rotate (it must be fully inside, see photos)
- from the start it may be tough to move, but that is intentional, after a while of moving it should be easier
Load test:
- hanged on it 5kg (on one hook) and it was looking good