1 / 8
3.00MM filliament Wade's Reloaded Extended height Hexagon Mount Extruder — zdjęcie 1
1 / 8

3.00MM filliament Wade's Reloaded Extended height Hexagon Mount Extruder

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This is a slightly modified 3.00mm filliament variant of DiscoJohn's Taller Extruder Mount.

Ocena
0 / 5
Polubienia
2
Pobrania
26
Wydruki
0
Wyświetlenia
279
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

This is a slightly modified 3.00mm filliament variant of DiscoJohn's Taller Extruder Mount. This version removes some material from the "wing" section and uses a slightly shorter bolt. This is designed to bolt to the upper mounting bolt of a Taz 3d printer, and requires a hexagon hotend. The Idler arm, latch and Extruder Spacer are not my work, and are included here for conveniance only.

Why a taller extruder mount you ask? Why add the extra plastic weight? The reason is simple. by extending the extruder body up to the upper bolt hole, you allow the extruder to tie directly into the carriage mount structure, which eliminates front to back nozzle flex. Without this taller mount, a stock taz toolhead can flex +/- 0.15mm forward or backwards, particularily on corners when the extruded plastic drags on the part during a vector change. This eliminates that issue entirely. This fits the Taz 6 style carriage or my own reinforced carriage here http://www.thingiverse.com/thing:1113697

If you wish to use the stock Taz 4 or 5 carriage, try this one instead. http://www.thingiverse.com/thing:755184

Print instructions

Category: 3D Printer Extruders Summary

This is a slightly modified 3.00mm filliament variant of DiscoJohn's Taller Extruder Mount. This version removes some material from the "wing" section and uses a slightly shorter bolt. This is designed to bolt to the upper mounting bolt of a Taz 3d printer, and requires a hexagon hotend. The Idler arm, latch and Extruder Spacer are not my work, and are included here for conveniance only.

Why a taller extruder mount you ask? Why add the extra plastic weight? The reason is simple. by extending the extruder body up to the upper bolt hole, you allow the extruder to tie directly into the carriage mount structure, which eliminates front to back nozzle flex. Without this taller mount, a stock taz toolhead can flex +/- 0.15mm forward or backwards, particularily on corners when the extruded plastic drags on the part during a vector change. This eliminates that issue entirely. This fits the Taz 6 style carriage or my own reinforced carriage here http://www.thingiverse.com/thing:1113697

If you wish to use the stock Taz 4 or 5 carriage, try this one instead. http://www.thingiverse.com/thing:755184

Print Settings

Printer Brand: LulzBot

Printer: TAZ 5

Rafts: No

Supports: No

Resolution: 0.5mm nozzle

Infill: 85% or better

Notes:

It's an extruder body, so ABS or higher temperature material is reccommended. Pre generated built in support.

Post-Printing

Instructions

Print as normal, remove the built in support from the bearing pocket and the idler arm, install Extruder hardware as usual. You will need a longer bolt to replace the stock M3 extruder mount bolt (50mm long M3, they are generally difficult to find locally) . I also usually glue the extruder spacer to the extruder body for conveniance in mounting.

Tagi