Tower/clever crane and container for wooden track - Brio and Ikea compatible
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Wooden track crane - cabin could be mounted either on top of the small tower or the train car (clever crane) Some Ikea…
- Ocena
- 0 / 5
- Polubienia
- 31
- Pobrania
- 129
- Wydruki
- 0
- Wyświetlenia
- 1256
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Wooden track crane - cabin could be mounted either on top of the small tower or the train car (clever crane) Some Ikea Lillabo cars compatible accesories (tank and 20ft container, big boulder and wagon). Photos are of v0 and v1 (yellow cabin) with less perceptible door and windows and v2 (red cabin).
Print Settings
Printer:
Trilab Deltix
Rafts:
No
Supports:
Yes
Resolution:
0.2
Infill:
16%-25%
Filament:
Prusa / Fillamentum Black - PCTG; other colors-PLA
Black Prusa, other - Fillamentum
Notes:
All parts are set in best orientation for printing. Only the bewel gear with insert, undercarriage and track need supports this way (undergcarriage need to be printed in this orientation to make sure that the pin do not brake while you snap on the insert).
While printing hook print with a cooling tower and insert pause/filament change at the begining of layer at height 4.4.mm (or just before the cooling tower is printed on a layer 4.2 if your printer prints colling tower at the end of the layer)Insert an neodymium magnet. Push the magnet inside with some piece of wood (I used pencil).
For boulder I would like to endorse you to try Fillamentum Vertigo grey. It looks awesome.
Post-Printing
Material
Clever Crane
from Hardware store
2x M6 nut
1x M6x40 bolt
1x -3x26 or 28mm dowel pin (I prefer shorter one) for connecting the jib to the cabin
1x -3x10 mm dowel pin for connecting Hook to the jib
25cm 2mm twine
2x binding screw 5x30mm ( see the thing [Wooden train wheel for 5mm axle](www.thingiverse.com/thing:3161992 by Simarilius for instructions)
and four wheels by Simarilius
2x ring ferrite magnet 12mm with 2mm hole 3mm thick (I only get with 3mm hole and it is just fine)
2x furniture nail
See this page for refference
Tower crane
2x M6 nut
1x M6x40 bolt
1x -3x26 or 28mm dowel pin
1x -3x10 mm dowel pin for connecting Hook to the jib
25cm 2mm twine
2x M3 nut
M3x25mm partially threaded bolt (round head with inbus/allen drive)
Assembly
Crane Body
- put twine into the jib and make a knot
- connect the jib to the cabin by a longer dowel pin (use short one to get the distance right
- Drill 6mm hole in knurled M6 holder (It is designed this way for printing w/o supports)
- Insert M6x40 bolt in the the holder
- Insert to the cabin hole and put nuts on
- set the the distancel of knurled nut to the cabin with the first nut as slightly loose
- put twine through twine holder, make knot and insert it in between both nuts
- secure the twine holder by jamming both nuts against it as seen on the picture
Clever crane
Put wheels on axles and axles through the undercarriage. You can choose either Simarilius's wheels, or if you have tunnels in your track setup, you can use my 19mm wheelst to be able to ride it through the tunnel.
Put an insert onto the undercarriage and snap cabin on and you are ready to go. :-)
Tower crane
Insert M3 nut inside knurled nut holder - use the bolt for jamming it inside
Insert M5x30 bolt intothe slot in the insert with bevel gear
Insert M3x25 into the upper part of the tube (you might use pliers for that - protect the thread by using another nut on thread)
Put the two parts of the tube together and connect to the bevel gear with locknut (it should move freely but it should not be loose)
Screw the pinion on the M3 bolt and secure it with M3 nut.
Screw on the M3 inside knurled nut holder an jam together.
Category: Mechanical Toys