1 / 10
Dustshoe (suction) for 80mm HF-Spindle (CNC) - NEW: V2.2! — zdjęcie 1
1 / 10

Dustshoe (suction) for 80mm HF-Spindle (CNC) - NEW: V2.2!

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Edit 02.04.2021: Verstärkung des Oberteils, insbesondere im Bereich der Spindelklemmung Edit 28.11.2019: Ich habe die…

Ocena
0 / 5
Polubienia
10
Pobrania
136
Wydruki
0
Wyświetlenia
962
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Ideas
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Edit 02.04.2021:

  • Verstärkung des Oberteils, insbesondere im Bereich der Spindelklemmung

Edit 28.11.2019:

Ich habe die Absaugung aufgrund der eigenen Erfahrungen nochmals verbessert (V2):

  • 3-teilige Konstruktion - so lassen sich die Teile ohne Stützstrukturen drucken - das Oberteil wird mit dem Mittelteil mitttels 4 Stück Senkkopfschrauben M4x10 verschraubt.
  • Umlaufender Rand am Mittelteil - so verschiebt sich das Unterteil unter keinen Umständen
  • Magnete beidseitig (Mittelteil und Unterteil) - so stärkere Haltekraft für das Unterteil (unbedingt beim einkleben der Magnete auf deren Polarität achten!)
  • Zweireihige Schürze im Unterteil: Ich habe zuerst einen Streifen 0,5mm Weich-PVC angeklebt, dann in passenden Abständen (ca.12-15 mm) diesen eingeschnitten. Dann einen weiteren Streifen auf den ersten geklebt und diesen ebenfalls eingeschnitten - allerdings jeweils versetzt zu den Schnitten der ersten Lage! So entsteht eine sehr dichte und doch flexible und transparente Schürze.

Für meine CNC-Fräsmaschine mit 1,5kw-HF-Spindel (Luftgekühlt) habe ich eine Absaugung konstruiert. Das besondere daran:

  • Unterteil einfach abnehmbar (Magnethalter)
  • Beleuchtung innerhalb der Absaugung (LED-Band).

Das Oberteil wird direkt an dem Flansch der HF-Spindel befestigt. Hierzu wird eine pasende Schlauchschelle benötigt. Im Oberteil sind (EDIT:) 6 Stück Neodym-Magnete (8x2mm) eingeklebt.

Innerhalb des (EDIT:) Mittelteils gibt es einen 10mm breiten Absatz, an dem sich passendendes LED-Band (Wasserdicht!) ankleben lässt. Das Kabel wird durch eine anzubringende Bohrung im Oberteil nach außen geführt.

Im Unterteil befinden sich ebenfalls 6 Stück Neodym-Magnete (8x2mm) - sie dienen der Befestigung am Oberteil. Ich habe als Schürze transparentes PVC (0,5mm dick) verwendet und mit Sekundenkleber angeklebt (siehe EDIT oben!). I

ch habe das Unterteil mehrfach gedruckt und mit verschieden langen Schürzen beklebt - so kann ich je nach Fräserlänge das passende Unterteil ansetzen.

Zusätzlich wird also benötigt:

Für eure Anpassung an die vorhandene Spindel habe ich die CAD-Zeichnung als .step-Datei angefügt.

Viel Spaß beim nachbauen!


Edit 02.04.2021:

  • Reinforcement of the upper part, especially in the area of the spindle clamping

Edit 28.11.2019:

I have again improved the suction based on my own experience (V2):

  • 3-part construction - so the parts can be printed without support - the upper part is screwed to the middle part with 4 pieces countersunk screws M4x10.
  • Circumferential edge at the middle part - so the lower part shifts under any circumstances
  • Magnets on both sides (middle part and lower part) - so stronger holding power for the lower part (always pay attention to their polarity when gluing the magnets!)
  • Double-breasted apron in the lower part: I first glued a strip of 0.5mm soft PVC, then at appropriate intervals (ca. 12-15 mm) this cut. Then another strip glued on the first and this also cut - but each offset to the sections of the first layer! This creates a very dense yet flexible and transparent apron.

For my CNC milling machine with 1.5 kW HF spindle (air-cooled), I have designed a suction. The special thing about it:

  • lower part easily removable (magnet holder)
  • Lighting within the suction (LED strip).

The upper part is attached directly to the flange of the HF spindle. For this purpose a fitting hose clamp is needed. In the upper part are (EDIT :) 6 pieces of neodymium magnets (8x2mm) glued.

Within the (EDIT :) middle section, there is a 10mm wide heel to which matching LED tape (Waterproof!) Can be attached. The cable is guided through a hole to be mounted in the upper part to the outside.

In the lower part are also 6 pieces of neodymium magnets (8x2mm) - they are used for attachment to the upper part. I've used transparent PVC (0.5mm thick) as apron and stuck it on with superglue (see EDIT above!). I

I have printed the lower part several times and covered it with aprons of different lengths - so I can put on the matching lower part depending on the length of the milling cutter.

In addition, you will need:

For your adaptation to the existing spindle, I added the CAD drawing as a .step file.

Have fun building!

Print Settings

Printer Brand:

Prusa

Printer:

Prusa Clone

Supports:

Yes

Resolution:

0.2

Infill:

20%

Filament: 3D Freunde PLA

Category: DIY

Tagi