Dustshoe (suction) for 80mm HF-Spindle (CNC) - NEW: V2.2!
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Edit 02.04.2021: Verstärkung des Oberteils, insbesondere im Bereich der Spindelklemmung Edit 28.11.2019: Ich habe die…
- Rating
- 0 / 5
- Likes
- 10
- Downloads
- 135
- Makes
- 0
- Views
- 956
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Ideas
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Edit 02.04.2021:
- Verstärkung des Oberteils, insbesondere im Bereich der Spindelklemmung
Edit 28.11.2019:
Ich habe die Absaugung aufgrund der eigenen Erfahrungen nochmals verbessert (V2):
- 3-teilige Konstruktion - so lassen sich die Teile ohne Stützstrukturen drucken - das Oberteil wird mit dem Mittelteil mitttels 4 Stück Senkkopfschrauben M4x10 verschraubt.
- Umlaufender Rand am Mittelteil - so verschiebt sich das Unterteil unter keinen Umständen
- Magnete beidseitig (Mittelteil und Unterteil) - so stärkere Haltekraft für das Unterteil (unbedingt beim einkleben der Magnete auf deren Polarität achten!)
- Zweireihige Schürze im Unterteil: Ich habe zuerst einen Streifen 0,5mm Weich-PVC angeklebt, dann in passenden Abständen (ca.12-15 mm) diesen eingeschnitten. Dann einen weiteren Streifen auf den ersten geklebt und diesen ebenfalls eingeschnitten - allerdings jeweils versetzt zu den Schnitten der ersten Lage! So entsteht eine sehr dichte und doch flexible und transparente Schürze.
Für meine CNC-Fräsmaschine mit 1,5kw-HF-Spindel (Luftgekühlt) habe ich eine Absaugung konstruiert. Das besondere daran:
- Unterteil einfach abnehmbar (Magnethalter)
- Beleuchtung innerhalb der Absaugung (LED-Band).
Das Oberteil wird direkt an dem Flansch der HF-Spindel befestigt. Hierzu wird eine pasende Schlauchschelle benötigt. Im Oberteil sind (EDIT:) 6 Stück Neodym-Magnete (8x2mm) eingeklebt.
Innerhalb des (EDIT:) Mittelteils gibt es einen 10mm breiten Absatz, an dem sich passendendes LED-Band (Wasserdicht!) ankleben lässt. Das Kabel wird durch eine anzubringende Bohrung im Oberteil nach außen geführt.
Im Unterteil befinden sich ebenfalls 6 Stück Neodym-Magnete (8x2mm) - sie dienen der Befestigung am Oberteil. Ich habe als Schürze transparentes PVC (0,5mm dick) verwendet und mit Sekundenkleber angeklebt (siehe EDIT oben!). I
ch habe das Unterteil mehrfach gedruckt und mit verschieden langen Schürzen beklebt - so kann ich je nach Fräserlänge das passende Unterteil ansetzen.
Zusätzlich wird also benötigt:
- Schlauchschelle (ca. 70mm)
- 12 Stück Neodym-Magnete 8x2mm
- 4 Stück Senkkopfschrauben M4x10mm
- PVC weich, transparent (0,5 mm dick)
- LED-Lichtband (ich habe dieses verwendet: https://www.ebay.de/itm/DC12V-5M-5054-SMD-LED-Streifen-Licht-Stripe-Leiste-Band-Lichterkette-Warmwei%C3%9F-DE/174043998975?ssPageName=STRK%3AMEBIDX%3AIT&var=472859739035&_trksid=p2057872.m2749.l2649)
Für eure Anpassung an die vorhandene Spindel habe ich die CAD-Zeichnung als .step-Datei angefügt.
Viel Spaß beim nachbauen!
Edit 02.04.2021:
- Reinforcement of the upper part, especially in the area of the spindle clamping
Edit 28.11.2019:
I have again improved the suction based on my own experience (V2):
- 3-part construction - so the parts can be printed without support - the upper part is screwed to the middle part with 4 pieces countersunk screws M4x10.
- Circumferential edge at the middle part - so the lower part shifts under any circumstances
- Magnets on both sides (middle part and lower part) - so stronger holding power for the lower part (always pay attention to their polarity when gluing the magnets!)
- Double-breasted apron in the lower part: I first glued a strip of 0.5mm soft PVC, then at appropriate intervals (ca. 12-15 mm) this cut. Then another strip glued on the first and this also cut - but each offset to the sections of the first layer! This creates a very dense yet flexible and transparent apron.
For my CNC milling machine with 1.5 kW HF spindle (air-cooled), I have designed a suction. The special thing about it:
- lower part easily removable (magnet holder)
- Lighting within the suction (LED strip).
The upper part is attached directly to the flange of the HF spindle. For this purpose a fitting hose clamp is needed. In the upper part are (EDIT :) 6 pieces of neodymium magnets (8x2mm) glued.
Within the (EDIT :) middle section, there is a 10mm wide heel to which matching LED tape (Waterproof!) Can be attached. The cable is guided through a hole to be mounted in the upper part to the outside.
In the lower part are also 6 pieces of neodymium magnets (8x2mm) - they are used for attachment to the upper part. I've used transparent PVC (0.5mm thick) as apron and stuck it on with superglue (see EDIT above!). I
I have printed the lower part several times and covered it with aprons of different lengths - so I can put on the matching lower part depending on the length of the milling cutter.
In addition, you will need:
- Hose clamp (about 70mm)
- 12 pieces of neodymium magnets 8x2mm
- 4 countersunk screws M4x10mm
- PVC soft, transparent (0.5 mm thick)
- LED strip light (I've used this: https://www.ebay.de/itm/DC12V-5M-5054-SMD-LED-strip-light-strip-bar-band-light-wire-warm-white- DE / 174043998975? ssPageName = STRK% 3AMEBIDX% 3AIT & var = 472859739035 & _trksid = p2057872.m2749.l2649)
For your adaptation to the existing spindle, I added the CAD drawing as a .step file.
Have fun building!
Print Settings
Printer Brand:
Prusa
Printer:
Prusa Clone
Supports:
Yes
Resolution:
0.2
Infill:
20%
Filament: 3D Freunde PLA
Category: DIY