LayersFactory
Zgłoś model
1 / 3
Voron Prime Pellet Bucket — zdjęcie 1
1 / 3

Voron Prime Pellet Bucket

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Sarge013

Sarge013

@Sarge013

A bucket for holding the priming pellets made at the beginning of a 3d print.

Ocena
5 / 5
Polubienia
84
Pobrania
259
Wydruki
1
Wyświetlenia
2589
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Voron Parts & Upgrades
Licencja
Creative Commons — Attribution — Noncommercial
SzczegółyPliki (7)Wydruki i komentarze (Wydruki: 1) (Komentarze: 4)Remiksy (1)Kolekcje (176)Powiązane

A little bucket designed to hold small priming pellets made during the Print_Start macro.

There are 2 versions of it, one that simply bolts to the front of the frame, and the other is held in place by 2 6mmx3mm magnets to allow for easy removal/dumping of the pellets.

Each version has a 250/300/350 size bucket. Tested and confirmed fit on a 350 but the smaller sizes should fit.

 

I have provided an example (I have been using for over a month) of the priming macro below. This is for a 350 and it assumes you have already leveled the bed/gantry and have the proper z offset/auto_z calibration.

Obviously, use this macro as a guide/reference and check it over and understand what it is doing before going full send on it.

[gcode_macro PRIMING]
gcode:
    M106 S255                      ;partcooling fan max
    CLEAN                          ;call clean macro
    G1  X5 Y5 F15000               ;move to purge position
    G1  Z0.3 F3000                 ;move to purge position
    G91                            ;incremental positioning
    G1  Z0.2 E30 F3                ;prime hotend
    G1  Z2.0 E25 F30               ;purge and move up
    G1  Z4.0 E20 F60               ;purge and move up
    G1  Z2.0 E10 F240              ;purge and move up
    G1  Z10 F3000                  ;move up by 10
    G1  Y55 Z-18.25 F3000          ;move to wiping start
    G1  Y10 F3000                  ;wipe back
    G1  Y-10 F3000                 ;wipe forth
    G1  Y10 F3000                  ;wipe back
    G1  Y-10 F3000                 ;wipe forth
    G1  Y-55 F3000                 ;wipe end and kick off the poop pellet
    M107                           ;turn cooling fan off
    G1  Z2.0  F3000                ;move up
    M82                            ;extruder absolute
    G92 E0.0                       ;extruder reset
    G90                            ;absolute positioning
    M107                           ;partcooling fan off
#------------------------------------------------------------------------



[gcode_macro CLEAN]
gcode:
    M204 S6000                     ;set acceleration to 6000
    G1 X5 Y35 F15000               ;move to position
    G1 Z0.5 F3000                  ;move to position
    G1 Y1 F10000                   ;kick the prime tower off


#------------------------------------------------------------------------</code></pre>

Tagi

voronvorondesignvoron24r2