Samus' Varia Suit 1:2 scale (articulated) - MP3:C
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
1:2 articulated figure of Samus' Varia Suit from Metroid Prime 3
- Ocena
- 5 / 5
- Polubienia
- 124
- Pobrania
- 374
- Wydruki
- 0
- Wyświetlenia
- 3832
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Action Figures & Statues
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a 1:2 articulated figure of Samus' Varia Suit from Metroid Prime 3: Corruption. The model is from the game, extracted with Metaforce, and can also be found at the Models Resource dot com.
Most of these can be printed in a 200x200 bed, but the legs will need a larger space.
Instructions for assembly are included in a PDF file. Several parts are also grouped together by color. Arms and (most) of the leg pieces should be printed in gold colored filament, the upper torso in red or copper, the lower torso and inner thigh in yellow, and articulations should be printed in black. You will need: At least 3 rolls of gold (4 to be safer), 2 copper, 2 yellow*, 2 black, 1 green or silver for the cannon, and 1 transparent also for the cannon. View the attached .txt file for more details.
*Use yellow for a more toy-like look, for a game-accurate look, that will depend on the game you want to represent, but usually you should be good with a "brass" colored filament, or you can buy gold filament from two different brands, they won't look the same, and use the "worse" looking one for this.
UPDATE 4: I've begun the process of replacing the original geometry with bespoke surfaces for better quality prints. The end result is a part that does not look like it was extracted from a Wii game. Most articulations won't be affected since they already were original pieces, this is mostly for the visible outer armor pieces, but I have taken the oportunity to touch up some of the joints. The original low-poly parts will be removed from this page to prevent confusion, if you must have the older parts, they can be found in thingiverse, or I can DM them to you.
This will be a long process, but I'll make an effort to make steady progress. Assembly will be unaffected unless specified.
Parts remade:
*Pauldron, Pauldron End, and Elbow Cover, individual and GROUP files. Elbow Cover Left has been removed, print the rightside elbow cover twice.
*Arm_1 A and B, individual and GROUP files.
*Foot, Toe_bend and Ankle_guard, both individual and GROUP files.
*Hand_articulated, Forearm_front and Forearm_back, both individual and GROUP files.
*New wrist pieces: Wrist_1, Wrist_2, Wrist_ball_Hex and Wrist_Ball_Screw_Head, individual and GROUP files.
*Index_1, Middle_1, Ring_1, Pinky_1, Thumb_2 and Thumb 3, individual and GROUP files.
*Leg_1 In and Out, Leg_2 In and Out, Ring and Glow pieces.
*New Knee_2.
*New OPTIONAL glow pieces with hexagons engraved, use these or the regular glow pieces.
Files for the Arm cannon: https://www.printables.com/model/316956-samus-armcannon-metroid-prime
Assembly requires two ¼" x3" (M6 x 75mm) screws for the hips and a handful of 3/16" screws (or M5) of different lenghts for everything else, these are as follows:
Six - 3/16" x1" - 5mm x25mm (ankle and arms)
Two - 3/16" x1 1/2" - 5mm x40mm (elbow)
Two 3/16" x3" - 5mm x75mm (shoulder)
Two 1/4" x3" - 6mm x75mm (hip)
Four 3/16" x2 1/2" - 5mm x65mm (legs)
Six 3/16" x2" - 5mm x50mm (leg2, knees, torso, forearm)
Two 1/4" x2 1/2" - 6mm x65mm (cannon)
One 5/32" x1/2" - 4mm x12mm (wrist)
One 5/32" x1" - 4mm x25mm (forearm)
Use of lock nuts is recommended. The model has holes for more screws for extra securing, but the pegs turned out to be more than good enough, however they are still required for tightening the articulations.
Update 1: Changed the chest-torso_lock piece, it should be easier to insert into the chest part. This piece is not necessary if you use plenty peg_1 pieces.
Update 2: Instructions are done! Also included a few grouped pieces. More to come.
Update 3: More grouped pieces and improved instructions.
Print Settings
Printer Brand:
Hellbot
Printer:
Hellbot Magna 2 300
Rafts:
Doesn't Matter
Supports:
Yes
Resolution:
0.16 and 0.2
Infill:
10% and 20%
Filament: Gold, Yellow, Black, Grey, Copper and glow in the dark
Category: Video Games