the Makerlele - MK1
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
My new YouTube Channel: https://www.youtube.com/channel/UCnnw56J\_TeOsF4M\_F5pPPJQ This fully 3D printable ukulele…
- Ocena
- 0 / 5
- Polubienia
- 122
- Pobrania
- 211
- Wydruki
- 0
- Wyświetlenia
- 2579
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Music
- Licencja
- Creative Commons — Attribution
My new YouTube Channel: https://www.youtube.com/channel/UCnnw56J\_TeOsF4M\_F5pPPJQ
This fully 3D printable ukulele (save for bolts and strings) uses an acoustic transducer to carry the lower frequency sound created by the strings to a very thin membrane on the bottom of the body. The sound is focused and projected out of channels in the body to (hopefully) create a fuller tone with reasonable amplitude.
I am still working on the design of the head and tuners. Right now, to have a good gear ratio for the prototype, I made the gears almost comically large.
UPDATE!!
I'm refining the design of the geared tuner head but I wanted to test the tonality to see if I was getting somewhere so I quickly designed a test friction head and tuning knobs to try it out.
I have uploaded all the current parts for everyone to TEST this EXPERIMENTAL design! Have fun!
VIDEO: http://youtu.be/4xRkysNNRc4
A couple of notes: I am tweaking the body design. The bridge is a little wonky and the transducer pops right off! I have to think that one over a bit. The bottom membrane is only two layers thin. It is tricky to print and even trickier to remove from the platform. BE SUPER-CAREFUL TO NOT TEAR THE MEMBRANE OFF!
The sound the first prototype makes is bright as expected but it is pretty loud. A good sign!
NOTE: This friction head is for testing only, it will no longer hold a tune after a while without shims or other "friction-enhancers." The geared tuner is the solution to this, I'm just working to make it a better, more reliable print.
Stay tuned!
Print instructions
Category: Music Summary
My new YouTube Channel: https://www.youtube.com/channel/UCnnw56J\_TeOsF4M\_F5pPPJQ
This fully 3D printable ukulele (save for bolts and strings) uses an acoustic transducer to carry the lower frequency sound created by the strings to a very thin membrane on the bottom of the body. The sound is focused and projected out of channels in the body to (hopefully) create a fuller tone with reasonable amplitude.
I am still working on the design of the head and tuners. Right now, to have a good gear ratio for the prototype, I made the gears almost comically large.
UPDATE!!
I'm refining the design of the geared tuner head but I wanted to test the tonality to see if I was getting somewhere so I quickly designed a test friction head and tuning knobs to try it out.
I have uploaded all the current parts for everyone to TEST this EXPERIMENTAL design! Have fun!
VIDEO: http://youtu.be/4xRkysNNRc4
A couple of notes: I am tweaking the body design. The bridge is a little wonky and the transducer pops right off! I have to think that one over a bit. The bottom membrane is only two layers thin. It is tricky to print and even trickier to remove from the platform. BE SUPER-CAREFUL TO NOT TEAR THE MEMBRANE OFF!
The sound the first prototype makes is bright as expected but it is pretty loud. A good sign!
NOTE: This friction head is for testing only, it will no longer hold a tune after a while without shims or other "friction-enhancers." The geared tuner is the solution to this, I'm just working to make it a better, more reliable print.
Stay tuned!
Instructions
Print, bolt together, string, tune, and play!