7 Turn L-Band Antenna (right hand polarized)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Right hand polarized L-Band Antenna for receiving satellite downlink data (especially L-Band ACARS).
- Ocena
- 5 / 5
- Polubienia
- 13
- Pobrania
- 98
- Wydruki
- 0
- Wyświetlenia
- 756
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
General:
This is a right hand polarized L-band antenna, designed to receive L-Band ACARS.
For outdoor use, it has an antenna cover as well as a spacious base to house a LNA or SDR.
Depending on parts availability, material cost is around 45USD.
Required parts:
1x Stainless stell Pizza Dish as ground plain (or similar round metall plate with more than 25cm diameter)
1x ~2 meters of 4mm outer diameter copper tube serving as the antenna
1x panel mount SMA connector
16x M4 metal threaded inserts
16x M4x12mm allen key bolts
Optional Parts:
1x 4mm O-Ring with 90mm outer diameter, 82mm inner diameter
1x 2mm O-Ring with 60mm outer diameter, 56mm inner diameter
7x M5 methal threaded inserts and M5 bolts for mounting
Tools
- Soldering iron
- Stainless steel drills (3mm, 5mm and 7mm)
- Pliers
- Vegemite jar (or similar)
Printing recommendations:
| Material | PET-G (for outdoor use) |
| Layer height | 0.2 mm |
| Wall loops | 3 (4 layers for the antenna cover) |
| Infilly | Gyroid |
| Supports | No |
Assembly Instructions:
- Print all the parts with the recommended settings. The STL files have the parts oriented for printing without supports - Use automatic orientation for the STEP files. No supports are required.
The drill guide can be printed in any spare material.
- Use the soldering iron to press in the M4 threaded inserts into the printed parts:
3x in the Antenna Support
13x in the Bottom Clamp
- Find the center of the pizza dish and mark it.
- Align the center mark of the drill guide with center of the pizza dish and drill the 5mm and 7mm holes according to the numbers of the drill guide.
- Place the SMA panel connector in the 7mm hole and mark the mounting holes.
- Use the 3mm drill to make the holes for the SMA panel connector and mount it.
- Place the the Antenna Support onto the pizza dish and align the Bottom Clamp on the under side of the pizza dish. Optionally make sure to insert the smaller O-rings into it's respective slot on the Bottom Clamp.
- Use 3x M4x12mm allen key bolts to mount the Antenna Support and Bottom Clamp onto the pizza dish.
- Use the Vegemite jar (or a jar with similar dimensions) to form the 4mm copper tube into a spiral - pay attention to the winding direction.
- Insert the copper tube spiral into the Antenna Support.
- Use the soldering iron to solder the copper tube spiral to the SMA center post.
- Connect the LNA or SDR to the SMA connector.
- Make a hole for the cable into the Bottom Endcap and insert the cable through it.
- Close the Bottom Clamp by installing the Bottom Endcap and Bottom Front Lid with the M4x12mm allen key bolts.
- Place the Antenna Cover (optionally with the larger O-ring inside the slot) on the assembly and fix it in place with the M4x12mm allen key bolts. Make sure to align the holes correctly before installing the first allen key bolt.
IMPORTANT WHEN USING THE O-RING: To prevent unnecessary straining of the printed part and/or to prevent layer seperation, I recommend to place the Antenna Cover with the open side up (like a cup) onto a flat surface and then apply some light to moderate pressure onto the pizza dish/Bottom Endcap to compress the O-ring, so that the holes line up correctly, before installing the M4x12mm allen key bolts.
- Use the M4 holes (or optionally the M5 threaded inserts) to mount the antenna to your desired location.
Done!
If you have any questions, feedback or other suggestion, please feel free to leave a message or contact me using any other channel (Discord, Mastodon, Website,….)