Filament Sensor Mounting Clip For Cocoon Create Touch and Wanhao i3 duplicator plus Rev2.0 (Clips to NEMA17 motors)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
By Brian Khuu 2019 This is for a cheap filament sensor, that you can usually find on ebay.
- Ocena
- 3 / 5
- Polubienia
- 4
- Pobrania
- 19
- Wydruki
- 1
- Wyświetlenia
- 386
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution
By Brian Khuu 2019
This is for a cheap filament sensor, that you can usually find on ebay.
This time it will clip right on to the NEMA17 extruder motor of a Cocoon Create Touch
and Wanhao i3 duplicator plus.
Rev1: https://www.thingiverse.com/thing:3785976 - This one mount to the top of the printer instead.
Configuration that worked for me in doing filament change in octoprint
https://www.reddit.com/r/wanhaoi3/comments/gi7tqy/configuration\_that\_worked\_for\_me\_in\_doing/
Requirements:
- https://github.com/andrivet/ADVi3pp installed to touchscreen and marlin board
- Octoprint installed and configured to a Cocoon Create Touch or Wanhao i3 Plus printer
- https://github.com/kontakt/Octoprint-Filament-Reloaded plugin installed
- Cheap ebay filament switch
Filament Reloaded Plugin Settings that worked for me:
- Pin : 7
- Debounce Time: 500ms
- Switch Type: Normally Open
- Board Pin Mode: Board Mode
- Gcode: M600 X0 Y0
Pause Print is unticked
ADVi3pp is required for M600 gcode command support for smart filament change.Board mode is based on "raspberry pi pinout" that you can easily google yourself.
High debounce time since physical switches can be a little unreliable.
Untick pause print since the special command already does it for you.
Checking that it works
Go to http://octopi.local/plugin/filamentreload/status and check that you can see {"status":"1"} on each refresh.
Warn:
Colour code of the cheap ebay filament sensor is counter intutative. Don't assume.
Print instructions
Category: 3D Printer Accessories Summary
By Brian Khuu 2019
This is for a cheap filament sensor, that you can usually find on ebay.
This time it will clip right on to the NEMA17 extruder motor of a Cocoon Create Touch
and Wanhao i3 duplicator plus.
Rev1: https://www.thingiverse.com/thing:3785976 - This one mount to the top of the printer instead.
Configuration that worked for me in doing filament change in octoprint
https://www.reddit.com/r/wanhaoi3/comments/gi7tqy/configuration\_that\_worked\_for\_me\_in\_doing/
Requirements:
- https://github.com/andrivet/ADVi3pp installed to touchscreen and marlin board
- Octoprint installed and configured to a Cocoon Create Touch or Wanhao i3 Plus printer
- https://github.com/kontakt/Octoprint-Filament-Reloaded plugin installed
- Cheap ebay filament switch
Filament Reloaded Plugin Settings that worked for me:
- Pin : 7
- Debounce Time: 500ms
- Switch Type: Normally Open
- Board Pin Mode: Board Mode
- Gcode: M600 X0 Y0
Pause Print is unticked
ADVi3pp is required for M600 gcode command support for smart filament change.Board mode is based on "raspberry pi pinout" that you can easily google yourself.
High debounce time since physical switches can be a little unreliable.
Untick pause print since the special command already does it for you.
Checking that it works
Go to http://octopi.local/plugin/filamentreload/status and check that you can see {"status":"1"} on each refresh.
Warn:
Colour code of the cheap ebay filament sensor is counter intutative. Don't assume.