Bambu Lab X1C & P1P Extruder/Hotend Maintenance Clip - v2
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Two-piece symmetrical clip holds front extruder fan assembly to the side of the hotend during maintenance. Magnets!
- Ocena
- 5 / 5
- Polubienia
- 16
- Pobrania
- 55
- Wydruki
- 2
- Wyświetlenia
- 1232
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
First, I made a maintenance clip for my X1C, but it only had connectors on one side, and the design seemed a little off to me:
https://www.printables.com/model/558865-bambu-lab-x1cc-extruderhotend-maintenance-clip
Then, I spoke with a few members of the community here, and I realized that there's a good chance that the only difference between the X1C and the P1P is the fact that the wire connecting the fan assembly to the extruder/hotend is on the right, versus the left.
So I started from scratch, took the 47.5mm magnet-to-magnet distance, and created a new clip.
Stuck with the two-piece design, but made the left and right of each part the same. Center bar - which connects to the hotend/extruder - has the arc (male connector). Outside bar - connects to the fan assembly - is a straight bar (female connector).
The X1C fan assembly slides off to the left, so the arc is in the middle, and the straight bar is off to the left. The P1P fan assembly slides off to the right, so with the arc still in the middle, the straight bar connects off to the right.
The holes are where the magnets go. The BOM is like $10:
https://www.amazon.com/dp/B075PMBBY3
If you place the 5x8mm magnets into the four top magnets in the hotend/extruder and the fan assembly, they will naturally connect the way they should be. Remember: opposites attract!
The side of these magnets that face out, will go into each of the holes in the print. That is the correct orientation. If you flip the magnets accidentally, they will REPEL, which is literally the opposite of what you want. Make sure you confirm attraction/poles before you insert the magnets into the part's holes.
You have two options for magnet fit:
- Make the holes the correct size, using XY Hole Compensation. On my PLA, it ended up being 0.1mm for a nice tight fit, but you will need to test on your side, due to different materials' expansion/contraction amounts.
- Make the holes slightly larger, and use an adhesive that will work with the magnets and the type of material you're printing these pieces with. For PLA, Cyanoacrylate (CA/Super Glue) works great. Just make sure you cure it well.
As I prefer the friction fit, that's what I went with, and the magnet-on-magnet strength is absolutely not strong enough to pull the magnet out of a properly tightened hole. I moved a set of four magnets from one print to another print, and I really had to work/twist to remove the magnets. That's where you want it to be.
I've found that the arc in this center piece holds the PTFE tube away from the working area, and also gives you space to work on the area just below. With the magnets I specified in the BOM, the connection to the Bambu Lab magnets is pretty tight, but easy to remove with force. It feels like it isn't going to fall off, which is exactly what I wanted.
There are a few minor shortcomings, which I will fix in the next version (v3):
- You'll likely want to print with supports, especially on the female side of the connectors. The angle that I cut out is a little too steep, so that top point is basically an overhang. Sorry. I'll do better next time. I've found the supports are easy to remove, so there's that. I actually made the top of the magnet holes domes, so they should print without supports, but once you turn supports on automatic, it'll probably fill in those holes. Not a big deal.
- Printing with PLA, I find that the arc is very strong, in “Strength” mode at 50% infill. When I was removing the magnets from the test piece, I decided to test the arc by twisting - it twisted with a lot of force, but did not break. Feels like a solid design, although I might add 1mm or so to the arc to make it stronger. We'll see how the feedback comes back.
Overall, I'm very happy with this design, and I hope folks use it and maybe get inspired to have other ideas for ways to improve the design in the future.
As always, I love to hear your feedback! Any questions, comments, suggestions are very much welcome. I also LOVE to see makes of my designs, so please share those if you can.
I have one or two users on here who will likely print and test this design with the P1P. When it checks out (hopefully with a make or two!), I'll add the P1P tags, and P1P to the header/summary. (Edit 12 Sep 2023: looks like it works on the P1P. Hooray for symmetry!)
Thanks to everyone who gave me feedback on the v1 tool in public and private. Every time I improve the design on one of my models, it makes me very happy to see the progression over time. Sometimes you get too close to a design, and it's hard to see the flaws, or obvious improvements that could be made. I am always open to constructive criticism!