1 / 2
Dremel 3000 bench/desk mount — zdjęcie 1
1 / 2

Dremel 3000 bench/desk mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Sideways mount for Dremel 3000 that uses 5 x M4 heated inserts for clamping onto the Dremel and securing to a bench/desk

Ocena
5 / 5
Polubienia
60
Pobrania
517
Wydruki
3
Wyświetlenia
2212
Oceny
3

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
BSD License

Faklam made a Dremel 3000 mount on Thingiverse that secured by unscrewing the endcap and screwing it back on. It works, but Kurck made a nicer-looking remix also on Thingiverse that hugged the endcap instead, with mounting bolts further to the sides, which – crucially – makes the Dremel more stable when it's not bolted down.

Given the main goal was for me to hold the Dremel sideways, even if I didn't bolt anything together, I opted to take Kurck's design and adjust it to use the same washer-ish mounting method Faklam originally used. It hugs pretty well without the securing bolt installed on top for jobs that aren't too difficult.

What I didn't plan on was the raw quantity of curve adjustments I had to make to change all those dimensions. Took me a couple days to get the design finished. Most of the geometry has been redone from scratch, preserving the original aesthetic – mostly because I worked incrementally – which gave me an opportunity to tidy up a few things.

PRINT NOTES:

  • Print with supports on the rear clamp overhang. Organic supports are probably best, but SuperSlicer's generic rectilinear supports work just fine
  • 5 x M4 brass heated inserts needed (I used these from uxcell). I made the holes 7mm deep to provide padding for 6mm heated inserts so they wouldn't scratch anything 
  • I used an M4x20mm for the clamp, though an M4x18mm would work also. An M4x16mm might pre-bend the clamp section and I'd rather keep the bolt with the clamp than find a new one every time.

Changes from Kurck's remix:

  • Most cylinders on the model have double (or more) of the number of vertices, so the curves should be smoother
  • Front and back feet are a wider stance with small fillets, which also means:
  • Bottom footprint has no right angles, so the first several layers won't have any corners that might get weird
  • Adjusted some vertical positions and dimensions so they slice well with 0.2 layer heights (bit of a force of habit…)
  • Back feet have fillets vertically instead of only a single angled side to reduce chances of breaking off from bad geometry

I spent wayyyyy too much time on this, but did get one printed off in Polymaker black PETG. Unfortunately the inner diameter of the hole underneath the screw-on endcap was a slight bit too small, so I took a step drill, drilled it out to 3/4", and it fit like a charm. I also noticed it would be able to be 3mm thick instead of only 2mm thick and be sturdier. I then noticed that I had forgotten to boolean-divide the geometry for the M4 bolt on the clamp mount, only the brass heated insert, so I simply drilled a hole in mine and modeled one in so no drilling is required. All three of those changes were made to the Blender file as well as the STL/OBJ and are !! UNTESTED !! but should work without issue.
 

Current issues I'm unlikely to fix:

  • Geometry surrounding the M4 heated inserts on the feet is probably a slight bit thin for scenarios where full-speed kickback is likely. Fixing this would require remodeling a significant amount of geometry, so I won't be doing this unless it breaks on me and I need to secure it.
  • Curves running in the Y direction down the sides is a bit too segmented for my tastes
  • Faces running from the big clamp ring to the main flat part of the mount are quite visible and look horrid only in the slicer – I can't see nor feel them on the printed part

Given how the changes took me a couple days, I'd rather leave it to someone who knows Blender better than I do and can adjust curves way easier than I can than do it myself. There's also a nice looking X pattern when it's sliced in 0.2 layer heights thanks to the reversing direction of the shell layers that would be tricky to preserve while fixing any/all of the above three, which would take me even longer to do.

PLEASE NOTE: The STL Blender exports MUST be done with “Selection Only” or it will export the hidden 3D Dremel model I kept in from Kurck's design. Once exported, I used SuperSlicer's “Repair Mesh” feature to export an error-free OBJ file. I opened the OBJ file in Blender with Z up and Y forward and immediately exported another STL with “Selection Only” checked to produce an error-free STL file as well. You might want to do this if you remix the file

Tagi