1 / 2
Dremel 3000 bench/desk mount — image 1
1 / 2

Dremel 3000 bench/desk mount

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Sideways mount for Dremel 3000 that uses 5 x M4 heated inserts for clamping onto the Dremel and securing to a bench/desk

Rating
5 / 5
Likes
61
Downloads
511
Makes
3
Views
2,184
Reviews
3

Updated at source:

Model information

Category
Tools
License
BSD License

Faklam made a Dremel 3000 mount on Thingiverse that secured by unscrewing the endcap and screwing it back on. It works, but Kurck made a nicer-looking remix also on Thingiverse that hugged the endcap instead, with mounting bolts further to the sides, which – crucially – makes the Dremel more stable when it's not bolted down.

Given the main goal was for me to hold the Dremel sideways, even if I didn't bolt anything together, I opted to take Kurck's design and adjust it to use the same washer-ish mounting method Faklam originally used. It hugs pretty well without the securing bolt installed on top for jobs that aren't too difficult.

What I didn't plan on was the raw quantity of curve adjustments I had to make to change all those dimensions. Took me a couple days to get the design finished. Most of the geometry has been redone from scratch, preserving the original aesthetic – mostly because I worked incrementally – which gave me an opportunity to tidy up a few things.

PRINT NOTES:

  • Print with supports on the rear clamp overhang. Organic supports are probably best, but SuperSlicer's generic rectilinear supports work just fine
  • 5 x M4 brass heated inserts needed (I used these from uxcell). I made the holes 7mm deep to provide padding for 6mm heated inserts so they wouldn't scratch anything 
  • I used an M4x20mm for the clamp, though an M4x18mm would work also. An M4x16mm might pre-bend the clamp section and I'd rather keep the bolt with the clamp than find a new one every time.

Changes from Kurck's remix:

  • Most cylinders on the model have double (or more) of the number of vertices, so the curves should be smoother
  • Front and back feet are a wider stance with small fillets, which also means:
  • Bottom footprint has no right angles, so the first several layers won't have any corners that might get weird
  • Adjusted some vertical positions and dimensions so they slice well with 0.2 layer heights (bit of a force of habit…)
  • Back feet have fillets vertically instead of only a single angled side to reduce chances of breaking off from bad geometry

I spent wayyyyy too much time on this, but did get one printed off in Polymaker black PETG. Unfortunately the inner diameter of the hole underneath the screw-on endcap was a slight bit too small, so I took a step drill, drilled it out to 3/4", and it fit like a charm. I also noticed it would be able to be 3mm thick instead of only 2mm thick and be sturdier. I then noticed that I had forgotten to boolean-divide the geometry for the M4 bolt on the clamp mount, only the brass heated insert, so I simply drilled a hole in mine and modeled one in so no drilling is required. All three of those changes were made to the Blender file as well as the STL/OBJ and are !! UNTESTED !! but should work without issue.
 

Current issues I'm unlikely to fix:

  • Geometry surrounding the M4 heated inserts on the feet is probably a slight bit thin for scenarios where full-speed kickback is likely. Fixing this would require remodeling a significant amount of geometry, so I won't be doing this unless it breaks on me and I need to secure it.
  • Curves running in the Y direction down the sides is a bit too segmented for my tastes
  • Faces running from the big clamp ring to the main flat part of the mount are quite visible and look horrid only in the slicer – I can't see nor feel them on the printed part

Given how the changes took me a couple days, I'd rather leave it to someone who knows Blender better than I do and can adjust curves way easier than I can than do it myself. There's also a nice looking X pattern when it's sliced in 0.2 layer heights thanks to the reversing direction of the shell layers that would be tricky to preserve while fixing any/all of the above three, which would take me even longer to do.

PLEASE NOTE: The STL Blender exports MUST be done with “Selection Only” or it will export the hidden 3D Dremel model I kept in from Kurck's design. Once exported, I used SuperSlicer's “Repair Mesh” feature to export an error-free OBJ file. I opened the OBJ file in Blender with Z up and Y forward and immediately exported another STL with “Selection Only” checked to produce an error-free STL file as well. You might want to do this if you remix the file

Tags