1 / 4
Rahmen für Temperaturanzeige von TFA Dostmann — zdjęcie 1
1 / 4

Rahmen für Temperaturanzeige von TFA Dostmann

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Rahmen für Temperaturanzeige für Original Prusa Enclosure and IKEA LACK Enclosure

Ocena
0 / 5
Polubienia
1
Pobrania
12
Wydruki
0
Wyświetlenia
125
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Die originale LCD Temperaturanzeige für das Original Prusa Enclosure ist sehr schwer ablesbar und die Feuchtigkeit in der Einhausung ist für mich irrelevant. 

Für meine LACK Einhausung (in weiß) hatte ich früher ein TFA Thermometer gekauft, das mir besser gefällt. Man kann das Thermometer auch auf der Rückseite ausschalten.   

Für die Prusa Einhausung hab einen passenden Rahmen erstellt, der anstelle des originalen Rahmens verwendet werden kann (inklusive der Muttern auf der Rückseite). 

Eine Abwandlung des Rahmens erlaubt die Montage unter dem oberen Tisch in einem LACK Häuschen. Schrauben zb Blechschrauben 2,9 x 13 mm gibt es im Baumarkt. 

Alle Schraubenlöcher sind so, dass die Schrauben eingedreht werden müssen. Damit können sie nicht herausfallen und beim LACK Rahmen kann man mit leichtem Druck die Schraubenpositionen eindrücken und markieren. 

Die FreeCAD Dateien sind angehängt. 

Maßänderungen in den Sketches sollten keine Probleme machen. Im Zweifelsfall bitte alle Pad, Pocket, Fillet und Chamfer einstellungen notieren, die entsprechnenden Elemente von unten nach oben (neu nach alt) löschen und mit den alten oder angepassten Parametern neu erstellen.   

 

I find the original LCD temperature display in the Original Prusa Enclosure difficult to read and the humidity in the enclosure is irrelevant to me.

Previously I  had bought a TFA thermometer for my LACK enclosure (white), which I like better. In addition you can turn the thermometer off on the back.

I created a new frame for the Prusa enclosure that can be used instead of the original frame (including the nuts on the back).

A modification of the frame allows it to be mounted under the upper table in a LACK enclusure. Screws such as sheet metal screws 2.9 x 13 mm are available at hardware stores.

All screw holes are such that the screws must be turned in. They can't fall out and with the LACK frame you can press in and mark the screw positions with light pressure.

The FreeCAD files are attached.

Changes to dimensions in the sketches should not cause any problems. If in doubt, please note all pad, pocket, fillet and chamfer settings, delete the corresponding elements from bottom to top (new to old) and recreate them with the old or adjusted parameters.   

Printersettings

  • Resolution: 0.2 mm
  • Perimeters: 2
  • Infill: 15%
  • Supports: no

 

Thermometer:

TFA Dostmann Digitales Thermometer, 30.2028.01, ideales Kühlthermometer, mit Magnet und Handler, klein und handlich, schwarz, L 68 x B 25 (14) x H 43 (61) mm : Amazon.de: Garten

 

screws 2.9 x 13 mm

 

Tagi