'THE BEETLE' EnderXY Direct Drive and 5015 Fan Duct Mod for Sherpa Mini and Revo CR
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Didn't like the setup of the original EnderXY hotend. So I made it direct drive and have better cooling.
- Ocena
- 0 / 5
- Polubienia
- 16
- Pobrania
- 107
- Wydruki
- 0
- Wyświetlenia
- 1250
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution
Welcome!
Been working on an EnderXY kit I got and was not satisfied with the original hotend setup. it was just kind of weird and offset and made it hard to find a good duct to use. Leading me to make this…

Kinda wasn't to give it the name “Beetle” because of how the modded in EVA duct looks. Oh right I should mention that. I modified a couple parts from the EVA hotend system that most RatRig printers use. Stuck the 5015 fan on the back and put the nozzle in the middle of the rail. I'm using a Revo CR that I carried over from my original Aquila printer which it came from. Fit's pretty alright but some things to know:
- You WILL need to adjust your bed size in firmware so that you don't have the fan duct crash into the z-lead screws and you WILL lose some build volume towards the rear (looking for a way to fix this).
- I have included the fusion assembly if you wish to mod it. It was made here in this embedded link. Give them some props for their work because it must've taken a good long while.
- I have yet to design any probe mounts for this system. If you come up with any do let me know.
UPDATES
- (11/26/23) - Project uploaded
- (11/29/23) - Added note that you will lose build volume towards the rear of the machine. I'm looking for a way to fix this possibly by making a mechanism to move the bed forward since there is extra clearance towards the front. I'll update this page if I make that happen. Also looking at compatibility with the triple Z lead screw mod here.
- (11/30/23) - Made an adjustment that gains an extra 11mm back that was otherwise lost in the Y direction. Leaves the build volume coming out to be closer to 200x200. Also added fan shroud with option to use Prusa SuperPINDA style inductive probe. Finally added in some zip tie mount to the front of the Sherpa mount so that you can route your cables a little nicer. I got mine from FYSETC. All of the files and CAD have been updated.
- (2/19/2025) - Shoot this project is sorta dead sorry :/
Materials Needed
This is something I might try to improve upon later. But for now I used what I had lying around so if any parts are strange and you don't have them, I do apologize.
- ABS or ASA For Printing Parts (Do them to the Voron Part specifications for strength)
- Two M3 x 16mm Bolts (My design works with socket and dome top nuts)
- Nine M3 x 8mm Bolts
- Eight M3 x 10mm Bolts
- Two M3 x 40mm Bolts (I'm looking for a way to make this work with a more common and accessible size)
- Three M3 x 20mm Bolts
- Fourteen M3 Heat-set Inserts (15 if using superPINDA Probe)
- Five M3 Washers
- A 5015 Blower Fan
- A 4010 Heatsink Fan
- A Revo CR hotend
- A Sherpa Mini Extruder
- Some length of Bowden tube
- Set of Allen Wrenches
Assembly
Don't think I'd just throw ya out there to try and figure this out yourself. I put together a little assembly guide with pictures to assist you since my CAD model doesn't include any of the fasteners or inserts.
Step 1: Print all of the parts
Fairly self explanatory. I printed mine out of some 3DXTech ASA and Sparta3D Sparkle ABS+ on my Prusa Mini using the Voron specific print settings. Some parts will need support but I've had very good luck with things. Those parts are show below. The front fan I have displayed there is the version that uses the SuperPINDA probe mount. If you won't be using that, simply paint on supports over the steep arches on either side and you should be fine!


Other parts you'll need will simply print like this with no supports needed.

Step 2: Heat-Set Inserts
The size of inserts I chose were based off of what i had on hand. Those happened to be Voron spec inserts which can be found here. Pictures of those parts are shown below.

Two heat-set inserts on the top of the Remixed EVA Fan Duct Rear.

Four heat-set inserts go on top of the Back Bracket.

Two heat-set inserts on the Top Bracket.

Three heat-set inserts go into the Sherpa Mini Extruder Mount.

Lastly there are four heat-set inserts to put into the front fan mount. (Add in the extra one on the side SuperPINDA mount if you printed that version. You can secure it with a short M3 bolt that gets tightened into the probe body.)
Step 3: Carriage Assembly
This holds everything together. First we start with securing the belts. If you're following along in the EnderXY assembly guide, you will install the Front Bracket part instead of the metal plate that comes stock with the kit. For this you'll need four M3 x 10mm Bolts as well as the Front Fan Duct part. First start by guiding your belts through the holes and slots on the Front bracket until they're sticking out. Make sure the heat-set inserts are upwards. Then, affix the Front Fan Duct using the four M3 x 10mm Bolts. Notice that the stop slopes upwards! You will end up with something looking like this:

Step 4: Front and Back Carriage Assembly with Hotend
These next few assembly steps are a bit of a process but they are doable. They just require a bit of finesse. For this you'll need two M3 Nuts, two M3 x 40mm bolts, the standard D6xL5 spacers that come with the kit, and the Revo CR Hotend.

First install two M3 nuts into the Back Bracket. The holes are such that the nuts will slot in. Allowing for them to be tightened with assembly later.

This next step can be a little tricky. I found that laying the printer face down keeps the bolts in place. Also putting something down the hole to make sure the bolts thread into the nuts help as well.
You will take the Revo CR and slide it up into the Front Fan Duct. Then, insert the two M3 x 40mm bolts into the holes and keep them just shy of emerging from the other side. Using tweezers, place the spacers between the heatsink and the Front Bracket. Push the bolts through to the other side.

You will then put the Back bracket over the bolts and work with it so that the bolts thread into the nuts. When tightening it down, be careful to not over tighten. Also make sure that the top is level with both sides.
Step 5: Carriage Assembly Rear 5015 Mount with Hotend Duct
Once more you'll benefit from turning your printing a bit with this step. For this step you'll need two M3 Nuts, two M3 x 20mm bolts, and the Remixed Fan Duct for the Revo CR.

First start by sliding the M3 x 20mm bolts through the rear of the back fan duct mount. This way it'll be held in place when you move to put the duct on the front.

Put the modified EVA duct over the holes and place the M3 nuts into their slots. Tighten the bolts from the back, and once finished you'll have the duct all secured! Be sure to test for tolerances and bed spacing. I have included the CAD to download if you need to adjust duct heights.
Step 6: Installing the Sherpa Mini Mount
For this section, you'll need nine M3 x 8mm Bolts, your Sherpa Mini Extruder, two M3 x 16mm bolts, and some bowden tube cut to 35.15 mm.

You'll first attach the Sherpa Mini to the mount using the two M3 x 16mm bolts to secure it on the right and left side, and one of the M3 x 8mm bolts to attach the front piece for extra stability.

After that, use eight M3 x 8mm bolts to secure the Sherpa Mini mount to the entire carriage. Once you get done with this, things will get much sturdier.
Step 7: Installing the Fans
Woohoo you're almost there! This is the last step before everything will be assembled. Minus the firmware changes you'll need to do. For this final step, you'll need your 4010 heatsink fan, the 5015 Blower Fan, four M3 x 10mm bolts, a single M3 Nut, and a M3 x 290mm bolt.

Before anything else, take a knife and cut off this little clip that is on the 5015 fan. It'll get in the way.

Gently slide the fan into the rear duct making sure to not split the printed part at the layer lines. Once it is in place, insert the M3 x 20mm bolt through the front face of the fan out to the back of the fan support. Slot an M3 nut into that space and tighten the bolt into it. As you can see here, I tightened too much and I broke the part. But the fan still held strong.
Lastly you'll install the front heatsink 4010 blower fan. Do this using the four M3 x 10mm bolts directly into the heat-set inserts. Once you do that, you're all done!

Excellent work! If you have any questions about the build or would like for me to try and make some simple mods just let me know in the comments! Feel free to give this a heart as well!
Closing
I'll post any updates and comments about the project as well as dates for anything significant at the top of this description. I'd love to hear some feedback from you all on this as well as some other mods! I'll be testing mine a good bit once i finish building the machine, but i wanted to get this out here for anyone who might need it! Thanks for reading and enjoy!~