1 / 1
Improved/modified/additional N90 parts
Zamów wydruk tego modelu
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Some parts to improve your experience with the N90
- Ocena
- 1 / 5
- Polubienia
- 34
- Pobrania
- 125
- Wydruki
- 0
- Wyświetlenia
- 1401
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
SzczegółyPliki (6)Wydruki i komentarze (Wydruki: 0) (Komentarze: 8)Remiksy (0)Kolekcje (41)Powiązane
1pcBP:
- removes the option for a magnetic buttplate
- uses M5x10mm nuts and screws to attach to the rear instead
barrel:
- to attach the muzzle! not included in the original fileset, but it is designed for this other muzzle…
- mine friction fit with the help of a mallet, mileage may vary
muzzle:
- modified to fit the other way round
- slightly resembles an actual P90 muzzle
nut holder:
- reinforced, thicker walls, can take a little more force than the original
- more tight fitting into the left and right halves of the blaster
- May require light filing to press-fit
nightingale cage:
- designed for worker nightingale motors and flywheels
- requires an M4x40mm nut and screw instead of the M5
Personal print settings:
PETG, 4 walls, 20% cubic infill (100% for the nut holder), 0.2 layer height
only nightingale cage needs support
Personal N90 hardware list:
this is what I used for my build, hope this helps for yours!
front section:
- m5x25 nut and screw - 4pcs (outer and roller assembly)
- m4x40 nut and screw - 1pcs (nightingale cage)
- m5x30 nut and screw - 1pcs (top cover hinge)
- m5x10 nut and screw - 2pcs (N20 motor retention and magwell)
- m3x10 nut and screw - 1pcs (pinwheel retention, m3x12 screw may be needed if 10mm is too short)
- motor screws - 4pcs
- m5x30 metal dowel pins - 6pcs (guide roller pins)
- m5.2xD8xL10 metal bushings - 7pcs (replaces the printed guide rollers)
- 5mmx3mm cylinder-style magnets - 16pcs (12pcs for top cover, 4pcs for “screw cover left” and “screw cover right”)
rear section:
- m5x25 nut and screw - 2pcs (mag release and body to stock lower)
- m5x30 nut and screw - 1pcs (body to stock upper)
- m5x10 nut and screw - 2pcs (buttplate attach)
- springs - 2pcs (mag release and mag ejector, mag ejector spring recommended but optional)
electronics:
- worker nightingale motors and flywheels - 1pair (2 motors and 2 flywheels)
- N20 motor (500rpm) - 1pcs (pinwheel)
- Omron lever microswitch - 2pcs
- (https://outofdarts.com/products/21a-microswitch-genuine-omron-v-212-1c6-spdt)
- one more switch can be wired at the pinwheel, but idk how to do that. if you do, that's a total of 3 microswitches
- XT60 female connector - 1pcs
- wire (idk man however much you need)
wiring is similar to uhhh… a rapidstrike/flycore/cagefighter/auto-stryfe
Good luck building!