1 / 6
Abnehmbarer Wandhalter für Ikea Gewürzgläser ÖRTFYLLD/ Removable wall holder for Ikea spice jars ÖRTFYLLD — zdjęcie 1
1 / 6

Abnehmbarer Wandhalter für Ikea Gewürzgläser ÖRTFYLLD/ Removable wall holder for Ikea spice jars ÖRTFYLLD

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Magnetischer Wandhalter für Ikea ÖRTFYLLD/ Magnetic wall bracket for Ikea ÖRTFYLLD

Ocena
5 / 5
Polubienia
17
Pobrania
71
Wydruki
2
Wyświetlenia
989
Oceny
2

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

For English see below

Dieser Halter ist für 16 Ikea Örtfylld Gewürzgläser geeignet. Der "Glashalter" wird von 4 Magneten gehalten und kann zum Reinigen abgenommen werden. Der "Wandhalter" wird mit 4 Tesa Powerstrips unsichtbar auf die Fliesen geklebt, ohne dass gebohrt werden muss. Durch die vorhandene Öffnung können die Powerstrips bei Bedarf entfernt werden.

Zusätzlich benötigt werden:
4 x Neodym Magnete Durchmesser 10mm x 5mm Haftkraft 3,5kg (z.B. https://www.mtsmagnete.de/neodym-scheiben-magnete/scheiben-10mm-19mm/neodym-scheibenmagnet-10x5mm-vernickelt-grade-n52-magnetisiert-durch-5mm/a-2504)
4 x Powerstrips Large bis 2kg  (z.B. https://amzn.eu/d/7nRgb1s)
4 x Metallscheiben Durchmesser 20mm x 2mm (z.B. https://www.magno-sphere.de/metallscheibe-20mm-x-2mm-mit-loch-und-senkung-nickel/a-2189/)

Montage:
Die "Platten" und Metallscheiben werden mit Sekundenkleber in den "Wandabschluss" und die Magnete in den "Glashalter"eingeklebt. Die Magnete dürfen nicht in die Bohrung versenkt werden. Es ist ein kleiner Überstand nötig, dass sich die Magnete und Metallscheiben direkt berühren (= maximale Haftkraft). Die Powerstrips werden auf die verklebten Platten angebracht und an die Wand geklebt. Der Pfeil in "Wandhalter" muss nach oben zeigen.

 

Unbedingt beachten! Alle Verklebungen müssen wirklich fachgerecht ausgeführt werden: Ich habe es so gemacht:

  • Wo möglich Aufrauhen der Oberflächen mittel Schleifpapier Körnung 80 bis 120.
  • Entfetten der Oberflächen mit geeignetem Mittel (z.B. Aceton 100% rein). Dabei die Fliesen nicht vergessen ;-) Die entfetteten Flächen nicht mehr berühren.
  • Sekundenkleber Medium auftragen und die Teile für 10 Sekunden verpressen.
  • Klebestellen vor der Weiterverarbeitung oder Belastung 24 Stunden trocknen lassen.
  • Die Powerstrips sinngemäß verkleben (Herstelleranleitung beachten).

 

Aus rechtlichen Gründen schließe ich jede Haftung aus.

 

Translation DeepL:

This holder is suitable for 16 Ikea Örtfylld spice jars. The "Glashalter" is held in place by 4 magnets and can be removed for cleaning. The "Wandhalter" is stuck invisibly to the tiles with 4 Tesa Powerstrips, without the need to drill. The Powerstrips can be removed through the existing opening if required.

Also required:
4 x neodymium magnets diameter 10mm x 5mm adhesive force 3.5kg (e.g. https://www.mtsmagnete.de/neodym-scheiben-magnete/scheiben-10mm-19mm/neodym-scheibenmagnet-10x5mm-vernickelt-grade-n52-magnetisiert-durch-5mm/a-2504)
4 x Powerstrips Large up to 2kg (e.g. https://amzn.eu/d/7nRgb1s)
4 x metal disks diameter 20mm x 2mm (e.g. https://www.magno-sphere.de/metallscheibe-20mm-x-2mm-mit-loch-und-senkung-nickel/a-2189/)

Installation:
The "Platten" and metal discs are glued into the "Wandabschluss" and the magnets into the "Glashalter" using superglue. The magnets must not be sunk into the hole. A small protrusion is required so that the magnets and metal discs are in direct contact (= maximum adhesive force). The Powerstrips are attached to the glued “Platten” and stuck to the wall. The arrow in "Wandabschluss" must point upwards.

 

Please note! All bonding must be carried out professionally: This is how I did it:

  • Where possible, roughen the surfaces using 80 to 120 grit sandpaper.
  • Degrease the surfaces with a suitable agent (e.g. 100% pure acetone). Don't forget the tiles ;-) Do not touch the degreased surfaces.
  • Apply superglue medium and press the parts together for 10 seconds.
  • Allow the bonded areas to dry for 24 hours before further processing or loading.
  • Glue the Powerstrips in the same way (follow the manufacturer's instructions).

 

For legal reasons I exclude any liability.

Tagi