1 / 4
Alastor's Microphone Staff/Cane from Hazbin Hotel (Accurate Size!! Over 4.5 feet tall!)
Zamów wydruk tego modelu
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Fully modeled and assemblable! Only glue/plastiweld required!
- Ocena
- 0 / 5
- Polubienia
- 56
- Pobrania
- 332
- Wydruki
- 0
- Wyświetlenia
- 2022
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Props
- Licencja
- Creative Commons — Attribution — Noncommercial
SzczegółyPliki (16)Wydruki i komentarze (Wydruki: 0) (Komentarze: 14)Remiksy (0)Kolekcje (48)Powiązane
Hello!
Here is Alastor's Microphone/Staff/Cane? from Hazbin Hotel!! Most parts have some method of joinery to make sure the fitment is correct, so assembly is very easy, just requires glue or plastiweld. I personally recommend plastiweld, but a good Loctite super glue should work fine as well. Of course be careful when using either.
Printing
- Cane parts (BLACK)
Cane 7 can be printed without supports. Cane 0 will need some supports near the base, but ensure that there are no supports between the threads! As for the others, place them with the internal threads down and external threads above. For ease, you can group Canes 1-6 onto one build plate. The flat overhang in the bottom of the internal thread may need support, or can be bridged if you have your printer dialed in. I printed with supports just on that flat face and it was fine. Again, make sure your supports don't end up between the threads! Print all of these at infill of 20% or higher. 25% is most recommended for strength.
- Eye (RED)
This piece is kinda awkward due to the curvature. My recommendation is to print it vertically with supports at the base to prevent it from falling over, and to get the parts that overhand on the left and right. Print with low-ish infill (~10%)
- Mic Lower (BLACK)
Place upside-down (top face on the bed). I wouldn't recommend printing it on its back because the layer lines will look super obvious. Supports are just needed below the center of the eye and a tiny bit in the corners of the eye pocket as well. Print with low (~5%) infill.
- Mic Upper (SILVER or WHITE) (canonically white in season 1, but I think silver looks better in real life)
Place right-side-up on bed. No supports needed. Again, don't print on the back. Print with low (~5%) infill.
- Top base (RED)
Place with the bottom part (NOT the part with the two sections cut out) on the build plate. Some supports are necessary near the base. Print with low (~5%) infill.
- Large part (RED)
This part will need to be cut in two. I have provided it cut in two, but you can also do it yourself in Cura or PrusaSlicer. I would recommend printing it on its flat face, not on the face where the two parts join. Although this would result in some layer lines, this is done to reduce warping. If you feel confident in your printer's ability to not warp the print, then place a large brim (~1cm) on each part and place it on the bed where the two parts would join together. Print with low (~5%) infill. This can be printed in one piece on a Prusa XL or a similar sized printer.
Assembly
- Cane/Shaft
Remove the supports from the internal thread part of each part. These were printed with Fusion's default tolerances in threads, so they fit VERY tight. This was by design, as they hold really nicely once forced together. Keep in mind that they are not intended to come apart. Starting from bottom to top, thread the bottom piece onto Cane 1 leaving a small gap. Put some glue/plastiweld in the gap, then turn all the way shut. Repeat with all of the next pieces. Be careful with the top part (Cane 7) as the corners are sharp, I recommend using gloves or a rag to hold on with.
- Top
If you printed your Large Part in two pieces, glue them together. Then starting with Top Base, place the assembled Large Part in the larger semicircle with glue or plastiweld. The Eye must be press-fit into the Mic Lower. Using a rubber mallet with a rag over the eye, gently hammer it into place. It shouldn't need any glue. Then, place this assembled Mic Lower + Eye into the smaller semicircle and glue it to the Top Base and the Large Part at the same time. Then, glue Mic Upper on top of that, to the Mic Lower and Large Part. This part has no joinery, so make sure its lined up before gluing. Then attach the whole head assembly to the top of the cane with glue. Again, this part has no joinery so make sure it is centered.
Thank you!
Thank you so much for stopping by. If you built it, congrats!! And thank you for supporting me. Let me know in the comments if there are any questions, and please post your make as well!