Laminar Flow Plate for a 120mm PC fan (Low Profile)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A plate that helps orient the flow of turbulent air coming off a 120mm case fan. Useful for improving targeted air flow.
- Ocena
- 5 / 5
- Polubienia
- 18
- Pobrania
- 240
- Wydruki
- 1
- Wyświetlenia
- 1280
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Share Alike
A low-profile laminar fan duct for PC cooling. Now, I'm still trying to learn OpenFOAM, so there's still tuning to do on the blade angle and shape to improve things, but this works. I just think I can make it better. In the meantime, have my first pass to play with.
What does this do? PC case fans blow out turbulent air, which is great for cooling things 2 inches (5cm) from the back face of the fan, and then the direct air flow rapidly dissipates from there and bumbles around the inside of the case. Now, if you're like me, and you have a custom modded GPU that consumes 550w of power, you need more airflow (Preferrably as cool as possible with exterior air) to reach the GPU's cooler intake from the front of the PC and/or more air to flow with speed across the back of the GPU as well*.
You can use a grid of vanes, which actually provides the air with more directionality, but is noisier. Also, too laminar of a flow actually cools less well that turbulent air, so this tries to hit a middle ground of increased flow direction but minimal impact on noise.
Should you put one of these on the exhaust of a PC case, or in-between a heatsink and a fan on a cooler? No. That does not help or may even make performance worse. These are best placed on intake fans, over the back frame of the fan, with plate attached via M5 self tapping fan screws (standard screw size for PC fans), with the screw heads fitting into the countersunk recesses. If the screws are not recessing into the plate on install, you have it backwards and it won't help things :p
IMPORTANT NOTE:
After installing these, track system temps using something like hwinfo64. When you improve heat removal off the GPU, that can raise system temps throughout your case. Things like RAM and MOSFETs elsewhere in your system don't like excess heat. You may need to increase exhaust fan speeds to help remove the additional heat that will be in the system air, especially if your GPU was being thermally limited and now can sustain higher throughput.
PRINTING NOTES:
The model's been tuned to print PETG and be +/-.1mm in the X/Y, but PLA is probably fine for this (pending you're not heat soaking your case, you should stay below the glass transition temp). If printing PLA please scale the model to like 99.7% or so for a more ideal fit. I printed the sample of this in gold PLA cause it's what's in my printer right now and the print turned out nice. Best printed at .4mm nozzle at .2mm layers, cause at .1 or .15 with a .4mm nozzle introduces some print oddness near the central hub. Use 15% gyroid infill cause grid is garbage :p
*Asterisk note: If you have a GPU with a completely flat backplate, directional laminar flow across the back may not help and in fact may limit cooling. If your GPU does have a thermal interface material between the core and the backplate, the backplate is completely flat, and you need to cool it more, some little stick-on copper heatsinks would work well with this. Just use the kind that looks like a little grid and place them on the backplate over where the GPU core and/or VRAM would be (eg between/around the 4 equidistant screws on the back).