Prusa XL Nozzle Wiper - Toolless with Info & walkthrough
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Nozzle brush for Prusa XL to keep nozzles shiny and cobwebs away! Requires no fasteners and has swappable faceplates
- Ocena
- 5 / 5
- Polubienia
- 23
- Pobrania
- 62
- Wydruki
- 2
- Wyświetlenia
- 1225
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Hello everyone! I made this model to help with the occasional stringing and to keep the nozzles clean, as I believe this is pretty critical to maintaining dimensional printing accuracy when we do the calibration probing. Not just for first layer, but also during tool offset calibration when we use the calibration pin. It also looks great, and helps keep track of what nozzle is where! For those who are printing a lot or with rough materials, having the date the nozzle was changed may also be useful. I hope you enjoy, and it brings you clean nozzles =)
Parts for build:
- Sharp knife
- Silicone brush (One for 1H/2H, two for 5H) (Eg: https://www.3djake.com/3d-basics/silicone-brush)
There are no fastenings required as the assembly is press fit into the rear bar of the XL, but I have put in a bolt hole for an M3 in case anyone preferred to have a more secure mounting method, eg via the 3030 T-Nut printable part. I have not had any issues with mine after printing for several weeks, so I'm pretty happy to trust they'll stay there.
The only parts required for this are just very basic silicone brushes, which we will cut up. They do not need to be special in any way, I used the cheapest silicone basting brushes I could find. Silicone is important, as it has a melting point high enough to withstand what we want to do and is not going to cause nozzle wear as the brass brushes will.
Part of my reason for this design was to be able to include information about the nozzles at a glance, eg if this is in use by multiple people or you have a funky setup. I have therefore made a clear space on the front of the holder for text, and included several example pieces such as 0.4, 0.25, ObX (for the ObXidian hardened nozzles), but I am not an expert on printed text so have fun, and please post the prints! I'd love to see what people do with this as its my first uploaded model :)
It is a very straightforward build:
Step 1:
Print the models you want to use.
- You will need 5 of the Brush Holder, they are identical. Overhang at the back needs to be supported, I have put in supports that I found to work best. Organic hexagon with .4 tip.
- You will need just 1 of the Cutter
- And as many of the Faceplate as you want! I have provided the models as I found them best to print, but have fun and be inventive. 0.10 Fast was fine for me.
- A handy text printing tip I found is that the XL prints the lower numbered nozzles first, so put your accent colour in tool 1, and body in tool 2 to get better quality text.
Step 2:
While Step 1 is printing, we will prepare the brushes. All that is required is a sharp knife of some description, the sharper the better. I used a scalpel to good effect.
- The target is to have 5 roughly identical brush parts. The base (ignoring the bristles), should be about 12x10x10mm (see picture). DO NOT CUT THE BRISTLES YET. This is what the printed cutter is for, and we will do that later.
- The best eyeballing technique I found was to have 5 bristles wide by 4 deep, but this really doesn't need to be exact. As long as it fits into the brush holder without sticking out the front, it'll be fine :). If it doesn't quite fit, trim some more!

(Don't cut the bristles yet! This is just a reference to make it easier to see)
Step 3:
Assemble the brush holder with our cut silicone brushes, and put the top on to lock it in place. Align the faceplate rails with the brush holder vertically, and slide down. Sliding the faceplate onto the rails on the brush holder might be a bit tight the first time due to the close tolerance and require a bit of wiggling, but they are designed to be swappable later on if you fancy a different face plate so shouldn't be too difficult. Remember they SLIDE down from above, not clip over the front!


Step 4:
Put the brush holder assembly into the silicone wiper, and use the knife to cut at the slot height. I found this was the best height from my testing, and using the jig helps to get a nice flat cut group. If they are not totally square do not despair, it does not matter :)

Step 5:
You're all done! Insert the brush assembly into the bar below the nozzles, and adjust laterally by eyeball so the nozzle runs down the middle. It should push in quite easily, and stay there.

Hope this helps, and happy printing!