Bicycle Bottle Holder Bracket (Long)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Wstępna wycena dla PETG
2,42 € – 2,96 € netto (bez VAT)
Dla pliku: LongBottleBracket_0.15mm_PETG_MK3S_3h22m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 2,69 € netto (środek widełek).
- Masa podana przez autora
- 21 g
- Czas druku podany przez autora
- 3,36 godz.
- Materiał u źródła
- PET
- Materiał wyceny
- PETG
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
This is a parametric model for a frame-mounted bike water bottle or similar accessory requiring two studs.
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 44
- Wydruki
- 0
- Wyświetlenia
- 441
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor Sports
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Basic Model
This model allows installation of a cycling accessory on the circular portion of bicycle tube frame or seat post at a location where no factory installed studs are available. The bracket is secured to the bike with three tyraps in this particular case. The model is prepped for 5mm bolts and nuts. The nuts are press-fit into hexagonal recesses in the back of the bracket. 10mm bolts worked well in my particular case.
The bracket can be applied to any circular tube location on a bike, exercise equipment or similar. It can also be used for any similar accessory like a tire pump,
Background
This bracket was needed for an Aventon ebike. A good bike, but limited provisions for accessories. This fits below the seat on the “L” size Pacer model. For a bracket to fit the “R” model see "Bicycle Bottle Holder Bracket (Short)".
Parametrics
The model was built in Fusion 360. The basic features of this model include two mounting stud locations and three clamping locations. 5mm hardware is assumed, however there is a variable for the size of the nut inset.
The parameters are in millimeters and current settings are:
BikeTubeDiameter = 35.7
ClampWidth = 4
ClampDepth = 2 (this is the depth of the clamp slot)
CircumscribedNutRadius = 3.95
StudSpacing = 63
Printing
This model was printed in an upright position with a brim using PTEG with 0.15 layer height and 0.4 nozzle. The print took about 3 hours 20 minutes.
Installation
The bracket is shown with black tyraps for clamping. Alternatively stainless hose clamps, velcro straps, or similar could be used. The parameters noted above can be adjusted for your particular clamping method.
In order to firm-up the placement and minimize any shifting, I used a rubber backer on the bracket. I up-cycled a piece of old tire tube for the job. Note that the interior of the inner-tube is usually treated with a talc type powder to prevent adhesion to itself during manufacture and use. I removed the powder with lacquer thinner which had the added advantage of adding a tackiness to the rubber. The rubber also protects the bike tube from minor marking from the mounting bolt if it protrudes slightly.
Alternatively an adhesive of sorts could be used but the rubber tube backing can be easily relocated.
(Note that photo of installation is an earlier non-parametric version.)