ANSO - Bambu X1C Chamber heater + AMS dryer + Stand + LED

 The ultimate mod from ANSO Suspension for Bambu X1C includes a chamber heater and air circulation, an AMS dryer, a stand with a toolbox, an LED, and cooling for the MC board and step motor.

We made this mode to get the best printing quality with ABS and PC. 

Attention—you need basic electrical skills and an understanding of electrical circuits with relays. If you do not have skills - you can find many videos on YouTube or skip this mod. 

AMS dryer compatible only with ANSO - Dryer Hydra PRO AMS or  Hydra PRO

Part list:

STC-3028 220/110 or 24v - 1pc

STC-3008 220/110 or 24v - 1pc

500w 24v power supply analog link  - 1pc

Liquid Insulating - 1pc

AC-2-red switch - 1pc

Cable lugs - 1pc

M3 inert nuts - 30pc

Sunon PMD2404PBB2-A 24v - 3pc

Sunon 3510 12v MF35101V3-1000C-A1  analog item- 2pc  (optional - for MC board cooling) 

Sunon  HA60151V4-000C-999 aliexpress -  1pc (optional - replacement of stock for the power supply) 

Sunon  12V HA40101V4-1000C-A99  analog item - 2pc  (optional - for step motor cooling) 

Sunon PMD2412PTB1-A 24v aliexpress - 1pc

Tuya Wifi module 4CH 7-32V - 1pc

30A 6-60v voltage regulator aliexpress- 3pc

LM2596 voltage regulator - 2pc

Delay relay XY-J04 - 2pc

30a 24v relay module 2 channel version - 1pc 

24v 200w 155mm PTC heater  aliexpress- 1pc

24v 280c 80w PTC heater aliexpress  - 3pc

36*35*10mm radiator  aliexpress - 6pc

Silicone Sealing Bottle Straw Hole - you need 4pc (take 1 pack of 10)

24v LED strip (about 1.3m) and alloy profile/strip 20*2mm (about 1.4m)

M3 bolts and nuts of different sizes - most popular m3 10mm(about 50pc)

8mm*75mm steel rods - 6pc (optional  - to make a stand more stable, you can also print from ABS or similar)

About 3kg of plastic - we recommend ABS

Electric wires of the correct size for 2A and 10A

It took a long time and a lot of experiments to make this mod. Unfortunately, we do not have all the pictures to make a super clear step-by-step manual, but most of the work is straightforward and easy. If you have any questions, please ask. 

Some recommendations:

1. To mount the Chamber heater bottom, use m3 screws with holes inside the printer bottom and Chamber heater mount. Then put the heater to the bottom part and install it with the Chamber heater cover. Also you should drill the bottom of the printer or make another way for the heater and fan wires
2. For AMS Heater - you must drill the radiators in two places to fix it inside the AMS Heater unit with the screws. A heater must be installed between the two radiators inside.  Also, you must drill the AMS unit near the PTFE tube hole (look at the pictures).
3. Set up delay relay XY-J04 to 2 minutes for fans to prevent overheating after turning off the heater. 
4. STC-3008 - put the first sensor on the bottom of the heated, the second sensor at the nozzle height near the nozzle wiper
5. STC-3028 - put the sensor inside AMS near the PTFE tube port
6. For the led strip mount -cut the alloy profile/strip ends at 45 degrees - it will be fixed in the stand 
7. Use the 6mm spacer and m3 10mm screws to mount the relays to the stand. 
8. Use voltage regulator with as low voltage as possible to get the 60C degree  in AMS and printer chamber to prevent overheating 
9. To control the AMS heater, available 2 modes - 1. Permanent mode - to keep moisture in a given range (for example 10%) 2. Dryer mode - to control the temperature in a given range for some time (for example 60C for 8 hours)