Large Capacity Bird Feeder with Magnetic Roof, Removeable Suet Baskets
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Hanging bird feeder that can optionally use acrylic panels for seed storage and has removeable suet baskets.
- Ocena
- 5 / 5
- Polubienia
- 28
- Pobrania
- 79
- Wydruki
- 2
- Wyświetlenia
- 454
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor & Garden
- Licencja
- Creative Commons — Attribution — Noncommercial
Intro:
This is a large capacity bird feeder. It is modeled after a popular wooden one that has an interior chamber for seeds and baskets for suet.
Magnets are currently required if using the suet baskets. Magnets are optional for the roof.
Dimensions:
- With Baskets
- 276 (w) x 160 (d) x 181 (h)
- Without Baskets
- 170 (w) x 160 (d) x 181 (h)
Printer Size:
- Your build area needs to be at least 170mm (w) x 160mm (d) x 220 (h)
BOM:
- Magnets Optional
- (16) - 6mm (diameter) x 3mm (thick) magnets
- https://www.aliexpress.us/item/3256801223676003.html
- If not using the suet baskets, 8 are needed.
- (16) - 6mm (diameter) x 3mm (thick) magnets
- (2) m3 x 12-20mm bolts.
- Short length of cord (<6mm diameter)
- Optional: 3mm thick Acrylic panels
- I had some laying around and they are easy to cut to dimension
- If you don't have acrylic, I have included
Printing:
- 0.2mm layer height
- 10% infill is fine
- 3 perimeters
Assembly:
- If using magnets:
- Glue 4 into the roof and 4 into the top of the main body
- Glue 4 magnets into the sides of the body and 2 magnets into each basket.
- If not using magnets
- Make sure to print the version of the roof [Roof - No Magnets.stl]
- Note, the suet baskets require the use of magnets to be removeable.
- You can glue them permanently to the side of the feeder if not using magnets.
- Attach the crossbar to the main body using m3 bolts. As long as your bolt is >12mm it will work fine.
- Tie a knot and thread string up through the crossbar, up through the roof, through the tree hook, then back down through the roof and back through the crossbar.
![]() Mark the 3mm acrylic with the printed guide. | ![]() Using a straight edge, score one side of the panel deeply with a knife. Then, flip the panel over and quickly bend along the score line. |
![]() Panel with custom hole size by using NO top and bottom layers. Shown here is honeycomb infill with ~40% infill. |
- Acrylic Panels - cutting acrylic is actually pretty easy to do.
- Use the included acrylic cut guide to draw lines on your acrylic.
- The panel dimensions should be ~161mm (w) x 132 (h)
- The key dimension is the width. It needs to be 160-161.5mm wide.
- Using a straight edge, score the acrylic on one side using a utility knife.
- Flip the panel over then quickly bend the acrylic and it should cleanly snap along your score line.
- Use the included acrylic cut guide to draw lines on your acrylic.
- Printed Panels
- I used acrylic panels, but I included options for printed panels.
- You can print the panels with 2mm square holes. You can use solid panels. Or you can use the solid panels and adjust your slicer infill settings to create your own custom hole pattern (use no top and bottom layers so the infill will be exposed).


