1 / 26
Integrated boom mount for Jan Heylen's DIY GPS — zdjęcie 1
1 / 26

Integrated boom mount for Jan Heylen's DIY GPS

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This mount eliminates the need for the elastic strap to stay on the boom and allows harness lines to be closer.

Ocena
0 / 5
Polubienia
1
Pobrania
22
Wydruki
0
Wyświetlenia
194
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a boom mount to suit Jan Heynen's DIY GPS that integrates the elastic so you don't have to have the elastic stay on the boom.    It eliminates the two side tabs that appeared to some users to break.   Having no tabs means you can move your harness lines closer together.   It is designed to fit the BE180 GPS (M10) and a 2000mAHr battery.  You can use a smaller battery but this one allows about 20hrs sailing time on one charge.  If you want to use the larger BN220 GPS see my other print cases.

Edit: 16th Dec 2025.  I noticed a small error in the V3 main case design uploaded here previously. (small defect in the antenna housing part.).  This is corrected in the V4 case design.

Please note, you need to fill with potting epoxy to get a water proof device.

I use PETG filament for the case as this allows gluing of a polycarbonate cover.  If you use DiChloroMethane (usually sold as WELD-ON 3) as the glue it welds the polycarbonate cover to the case and is almost impossible to remove.

The photos hopefully show the process of assembling the unit but the procedure is as follows.

1) Flash the software onto the device.

2) Solder the reed switch, the GPS wires and (if using) the Lipo wireless charge receiver to the T5 paper display.  Plug the battery in and test your device thoroughly.  Don't procedure until you are sure it is functioning correctly.

3) Hot glue the charge receiver and electronics in place (or just insert if using a USB plug and play charge receiver).   Note before this step you might want to spray the case (outside only) with a clear spray...depending on the quality of your printer the epoxy may ooze slightly through the pores of the print

4) Slide the GPS into its slot ensuring the antenna is facing up

5) Put one or two small strips of electrical tape over the small rectangular strip near the flexible connector on the face of the display.  This area is photo sensitive and if exposed to direct sunlight it will make your screen ghost (or fade).  The tape and the 3D inside trim shield the sunlight from this area and it will maintain good contrast in bright sunlight.

6) Put the display in the case then the inside trim.

7) Cut a piece of 3mm polycarbonate roughly to shape but a little bigger (1-2mm) than required.  Peel the non see through side of protective tape off then clamp upside down on a bench.  Apply a tiny amount of DiChloroMethane around the edge of the case. (Note if you apply the glue before you clamp the glue often runs all over the inner cover spoiling its appearance)

8) Leave clamped for at least an hr, preferably overnight then do a final test of all functions of your GPS. Run a bead of hot glue around the entire polycarbonate to case interface....this stops the epoxy leaking.  If you don't have hot glue then use a bead of silicon (the stuff you seal bathrooms etc with) instead.

9) Use a 4mm drill (held in the hand) and clean the epoxy fill holes (depending how you oriented your print they may be slightly oval).

10) Mix up your potting epoxy.  It takes about 36 grams (30ml) to fill so you would mix about 40 grams to allow a little for reservoirs.   Keep your hot glue gun ready in case of any leaks.

11) Put an old syringe in one of the fill holes..this is one reservoir then proceed to fill the device from the other hole using another syringe. (You can purchase syringes in any pharmacy very cheaply).  Go slowly as high pressure can make the epoxy ooze through the print.  Don't push the plunger all the way otherwise this injects air.  Once epoxy starts flowing out the other reservoir it's a good idea to hold the device at various angles and continue filling to remove air bubbles.  Empty the reservoir back into your mixing container if required and continue injecting epoxy until no air bubbles come out.

12) Continue to hold your device at various angles to ensure all air bubbles are removed.  If there is an air bubble trapped between the polycarbonate and the inner trim then pushing on the face of the display can help pump the air bubble through the small gap.

13) Remove the filling syringe and replace with another used syringe to act as another reservoir.  Ensure each reservoir has a little epoxy.   If epoxy is leaking you can usually plug it with hot glue.

14) Periodically check on your device to ensure the reservoirs aren't draining (meaning a leak)

15) Once the epoxy is cured (usually 1-3 days) remove the reservoirs (reuse them) and remove the hot glue then use a small drum sander on a Dremel type tool to trim the excess polycarbonate.

16) Not entirely necessary but fill the little holes the reservoirs made with 5 min epoxy, remove the protective sheet off the polycarbonate then glue the outside trim in place.

17) Use 3mm shock cord.  For the leash I use 46cm of Diabolo string tied as shown in the photos.  You can purchase this online or any juggling/circus shop.

For more info please see the Seabreeze thread https://www.seabreeze.com.au/forums/Windsurfing/Gps/Another-DIY-GPS-logger-approach?page=-2

The Wiki on how to build https://docs.google.com/document/d/1XJD6BV1Xay4nXo0cDuo_IOtxC_f1LyG7DE7X6KGlAB0/edit?tab=t.0#heading=h.z6ne0og04bp5

More information on using the GPS https://docs.google.com/document/d/1j86kj3bNMID3sHCRT7QTYyrL7IHeQnGPec1LajsDfB4/edit?pli=1#heading=h.jat89aj37nmf

 

 

Tagi