21 modeli
This is a wingfoiling harnes hook I made. After testing different designs, this is a good strong design. It's easy to print. Settings, you can use PETG, which is strong and watter proof. (4 layers and 80% infill is a good idea).…
I have found that the inside of my wetsuit boots struggle to dry without being propped open, which is difficult to do, especially when away. So, I quickly designed this! These are designed to go inside your wetsuit boots to keep them…
Outhaul pulley for windsurfing. Keep them on your sail in each clew position for fast rig and on water changes. Cost is about 50 cents unlike commercial versions costing $30+ There are two designs to accomodate different pulley tube…
Holder for mast extensions (windsurfing, SDM, tube diameter 44 and 47 mm) The holder is tested on these rails: https://www.kurierbedarf.com/Airlineschiene-halbrund-05-Meter-light…
My decades old windsurfing board needed replacement boom cleat for its outhaul line. These are made to be easily printed without supports. Source files are also included. Please share your prints!
Rear facing shots at water level whilst windsurfing give awesome shots both of the high speed wake and your mates chasing you. This simple mount connects to the rear tuttle bolt. A piece of 3mm x 10mm Aluminium bar is the reinforcement…
Since a pile of people seem to be making these I thought I'd update the design based on lessons learnt. This is to house Jan Heynen's design DIY GPS (links at bottom) Note, this is NOT waterproof, it relies on filling the case with…
Couldn't justify paying $100+ for one of these things so quickly made my own. Made for 10mm pipe. I used 10mm plastic coated steel tube which I had lying around which had OD of 10.2mm and 1.5mm wall thickness. I printed at 100% infill for…
I needed a very low profile rack system for my gear as wind variation here extreme so need to pack lots in. Also needed to be able to quickly adjust the racks to suit various gear and also remove the whole rack system quickly in order to…
As the title states, its a fully printable windsurfing board, at least i hope it is. Based on the video from DZfoils, I made a few design changes in regards to the structure of the board. At first the plan was to go 100% printed, but i…
This is a modification to my original print that can be found here https://www.prusaprinters.org/prints/104363-windsurfing-speedo-doppler-gps-low-profile-counter This print adds a trim layer that makes the unit more professional looking…
After playing around with the basic downhaul winch design it was apparent it could be improved. The main improvement is the basic design could fail under high loads due to the torque applied tending to separate layers of print so added 4…
Air valve for windsurfing PETG When printing, place the screw horizontally with support. This is a slot for an air valve for windsurfing. I had one board that didn't have this valve. Put a rubber washer under the screw and don't tighten…
With Windsurfing records now exceeding 100Km/hr there is a real need for an accurate feedback for sailors. All previous systems have relied on a watch screen (impossible too see at high speed) or some sort of audible feedback. Most are…
Trying to get underwater footage of windsurf fins to understand them better and get different action shots. This one is non destructive for the board for GoPro 9,10,11 and relies on a small piece of clear poly carb matched exactly to the…
This fin cam relies on cutting a hole in your board…here where I live people seem to throw out perfectly good boards so scored a few donor boards to try this out. Scored a near perfect 2006 iSonic 111 just a few meters from my house…how…
I picked up a free windsurfing board and it was missing a fin so I made one up for it. It fits a US-Slot style board. Dimensions of the slot part are 8x145x35mm with a 4mm hole and 5mm pin. Total height of the fin (including slot) is…
A handy storage unit identifier for my Windsurfing gear closet.
Wall mount for windsurfing booms
Windsurfing batten top rod for 10mm carbon batten For sure fit duotone and neil pryde carbon sail battens. Carbon version require 6 mm carbon rod glued inside. Only carbon version is very stiff, other one should be used until you find…
I made these extension rings for my uncle who is a windsurfer. I didn't truly understand what the rings were for, but I share them anyways. The dimensions Inner diameter: 32.6mm Outer diameter: 41mm (to match the plastic part that covers…
