Print in Place Flexi Fridge Magnet
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
0,33 € – 0,40 € netto (bez VAT)
Dla pliku: AlienstickyDome10_0.2mm_PLA_MK3S_30m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,37 € netto (środek widełek).
- Masa podana przez autora
- 2 g
- Czas druku podany przez autora
- 29,4 min
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
This is a Print in Place Alien Sticky Bomb Fridge Magnet The Defender Cosplay Prop that Alexia Harmon uses.
- Ocena
- 5 / 5
- Polubienia
- 87
- Pobrania
- 315
- Wydruki
- 4
- Wyświetlenia
- 1894
- Oceny
- 4
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Props
- Licencja
- Creative Commons — Attribution — Share Alike
This is my interpretation of the Sticky bomb that is fired from the fictional story The Defender written by Larissa Soehn.
The book The Defender, by Larissa Soehn can be purchased from Amazon.ca https://www.amazon.ca/dp/0228866030/ref=cm_sw_em_r_mt_dp_C45MY5Y5MX8X238XASPZ
Amazon.com
https://www.amazon.com/dp/0228866030/ref=cm_sw_em_r_mt_dp_1REWZVEF7VVPNPZM1Q5S
In the book Alexia is plunged into an Alien world where she is forced to test her abilities immediately upon arrival to determine her "Threat Level". During of these tests she is given a two triggered bomb launcher that fires a 6 legged sticky bomb and then detonates it.
I wanted to design a Print in Place model for this design that is loosely modelled off the Octopus designs that you see floating around the internet.I figured it would also be cool to make it a fridge magnet to capture the "stickiness" mentioned in the book.
The Model fits 2 different sizes of magnets if you want, but really you can get away with the smaller of the 2 since they fit into each leg and allow you to pose the model on a metal surface.
The magnets I used were
6mm diameter x 3mm high for the leg magnets
12mm diameter x 2mm high for the central magnet.
Purchased from amazon.ca
https://www.amazon.ca/dp/B07WCN5FGD/ref=cm_sw_em_r_mt_dp_TF0S2ZFMG0P5DV7BF5M9?_encoding=UTF8&psc=1
and
https://www.amazon.ca/dp/B07GX7Z4DF/ref=cm_sw_em_r_mt_dp_ZT22HT5TT46R086EKF5Q?_encoding=UTF8&psc=1
Print in place, Pop off Bed
I added the various pieces and spikes in order to prevent needed a raft or Brim. It should be able to be printed right onto the bed. I have had plenty of success and I wish you all the best (every printer is a bit different but I was getting repeatable results with this design and my printer.
It took me 8 attempts to get the legs right. The very first time I printed it off too small, then I worked on getting the right range of Motion, then I worked on ensuring I could get repeatable results without any Brim.
I created a bit of a Dome of the design so you could put anything into it.
I designed this because I also wanted to deign the a Cosplay Bomb Launcher Prop, that this could fit inside. I started here to get the right dimensions. The Cosplay Bomb Launcher Prop is coming soon.