SoShine 6W panel and Enclosure Mount using 3/4" EMT (modular design)

Modular system for mounting a SoShine 6W 5V solar panel, enclosures and various other things using 3D printed parts (out of ASA, ABS or other outdoor filament) and EMT conduit found at your local hardware store.

This is an active project, so there will be changes and additional parts as I go.

The printable parts:

• EMT Plug
  • Plug the end of your ¾" EMT conduit so stuff doesn't get in there and it doesn't cut you.
• EMT Elbow (may be a little easier to print)
  • Use This to join two pieces of EMT conduit perpendicularly.  
  • Use hose clamps to tighten them.
• EMT Elbow 2
  • Has alignment hole for a rod to align other parts together.
• MeshtasticNode_Panel_Box_Bracket_Small
  • Mounts a commonly used enclosure to a piece of EMT conduit.  This is for the smaller box (5.9" x 3.9" x 2.8")
• MeshtasticMediumBoxEMTMount
  • Mounts a commonly used enclosure to a piece of EMT conduit.  This is for the medium sized box (7.9" x 3.9" x 2.7")
• Meshtastic7mmIDFastenerWasher
  • This is a washer to use when fastening the solar panel to the braces
• Meshtastic7mmFastener
  • This is a fastener to put through the solar panel holes, through the washer (above) and secure with a wire (I use some stainless welding wire).  It's cheaper than ordering a bunch of nuts and bolts from McMaster.
• SoShine6WattSolarPanel3DPrintEMTMount.3mf
  • One of two arms to mount the SoShine solar panel to the EMT conduit.  It's a 3MF because Solidworks keeps exporting into STEP with some errors that I clean up in BambuStudio.  STEP and 3MF give me smooth curves to fit the EMT nicely, where STLs are faceted.  (I will eventually get frustrated and redesign this).
  • The angle is 33° or 123° from flat for holding your panel at that angle.  
• SoShine6WattSolarPanel3DPrintEMTMountTreeTabs.3mf
  • This is the same as the above, but it has a plate for mounting to a board or a tree.
• EMT_WallMount
  • This lets you mount a piece of EMT to a vertical wall.

Here are the parts that these prints interface with:

• 5V 6W SoShine solar panel:
  • https://www.amazon.com/gp/product/B099RSLNZ4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
• Medium (7.9" x 3.9" x 2.7") Enclosure/Junction Box
  • https://www.amazon.com/gp/product/B07KXVQ88B/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
• Small (5.9" x 3.9" x 2.8" Enclosure/Junction Box:
  • https://www.amazon.com/gp/product/B07KXRW62F/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
• ¾" EMT Conduit (Common Commodity Part)
  • https://www.homedepot.com/p/3-4-in-x-10-ft-Electric-Metallic-Tube-EMT-Conduit-853429/100400406
• Hose Clamps (Common Commodity Part)
  • https://allfasteners.com/hose-clamps-304-stainless-steel.html