1 / 18
Lighthouse "Lange Jaap" + mod-1 — zdjęcie 1
1 / 18

Lighthouse "Lange Jaap" + mod-1

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Lighthouse scale 1 : 200 with (optional) simulating light

Ocena
0 / 5
Polubienia
6
Pobrania
55
Wydruki
1
Wyświetlenia
224
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike
Model of Lighthouse "Lange Jaap"

Location: Huisduinen NL
Scale  1 : 200 (height 31,5 cm)

Optional: simulating light (Fl(4) 20s) using a ATTiny (13A, 45 or 85)

History of the lighthouse.

The designer of the lighthouse was Quirinus Harder. 
In 1877 the construction of the Lange Jaap began. 
The sixteen-sided tower is made entirely of cast iron plates with a raised edge that screwed together, making the lighthouse very heavy (506.100 kg of cast iron). 
With a height of 63,45 meters, LangeJaap is the tallest lighthouse still burning in the Netherlands and the tallest cast-iron tower in Europe. 
The climb to the top has 284 steps.

Update/Modfication.

- modification 01 (dec 2024).
   the model has now an option for a wider footprint and pedestal wich include several battery      case options.
   new parts:
 . part 01a - Groundplate to convert the old battery base to the fit the univeral base
 . part B0a - AA Battery base
 . part B0b - AA Battery case (3x AA size) 
 . part B0c - AA Battery case lid 
 . part 02a - Tower low mod1 (replaces part 01, 02, 11 and 12)

- modifiction 01a (jan 2025).
 Add two more options for battery bases an AAA and 18650 model.
 . part B1a - AAA Battery base
 . part B1b - AAA Battery case (3x AAA size) 
 . part B1c - AAA Battery case lid 
 . part B2a - 18650 Battery base
 . part B2b - 18650 Battery case  
 . part B2c - 18650 Battery case lid 
 

I build this model after i found the drawing from 1877 on internet and because the tower has some cracks in the onstruction it is pending if or when he will fall over, besides that I see the lighthouse every day.
Al parts are printed in PETG but PLA is also fine (just don't place the model in the sun).

Printer settings:
- 0.15 detail layer for parts 05, 06, 08, 09 and 10
- 0.2mm quality for the other parts 
- infill 15%
- nozzle 0.4mm
- brim for part 02, 03 and 10 radar print upside down
- Support for Base & Batt section and lower section using enforced support

Options:
- Just build the tower without light;
 . Print the parts 01-10 and glue the together, no need to print parts
 . Print part 00a if you like to raise the model by placing it on a pedestal.

- Build the tower with the working light;
 . Print all parts, 
 . Fist glue together part 03, 04, 05, and 06 then part 08-09 (place a piece of silverfoil                  between them to
   prevent light shinging thru the roof) and 10 the radar.
 . Don't glue part 07 on part 06 it have a snug fit, place Led (wires already soldered on) and          place the glued parts 05-08 over part 6, glue after testing the light not before!

The following filament colors are used:
- Dark Red for the tower
- Beige ad Dark Grey for the groundplate and first base (colorchange)
- Transparent for part 
- White for part 04, 06 and 08
- Dark red for part 07

If you decide to put the Lighting option in the tower you need extra:
Hardware:
- Led 5mm bright white or bright warm white (is more realistic)
- Resistor 33 or 47 Ohm (smd 1210 or 1206 version)
- ATTiny 13A, 45 or 85 dip version
- Dip 8 socket (bent legs to make surface mount version)
- Slide switch (micro)
- 3mm screw for the battery case lid
- Electrical wire approx 50cm red and black
- PCB is optional

If you decide not to use a PCB you can solder the wires directly to the ATTiny but;
Make sure to program your ATTiny first and test it before soldering wires to it.

Additional files:
- Electronic scheme 
- Pcb surface mount layout 
- Arduino sketch

Tagi