Lighthouse "Lange Jaap" + mod-1
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Lighthouse scale 1 : 200 with (optional) simulating light
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 55
- Makes
- 1
- Views
- 224
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Architecture & Urbanism
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Model of Lighthouse "Lange Jaap"
Location: Huisduinen NL
Scale 1 : 200 (height 31,5 cm)
Optional: simulating light (Fl(4) 20s) using a ATTiny (13A, 45 or 85)
History of the lighthouse.
The designer of the lighthouse was Quirinus Harder.
In 1877 the construction of the Lange Jaap began.
The sixteen-sided tower is made entirely of cast iron plates with a raised edge that screwed together, making the lighthouse very heavy (506.100 kg of cast iron).
With a height of 63,45 meters, LangeJaap is the tallest lighthouse still burning in the Netherlands and the tallest cast-iron tower in Europe.
The climb to the top has 284 steps.
Update/Modfication.
- modification 01 (dec 2024).
the model has now an option for a wider footprint and pedestal wich include several battery case options.
new parts:
. part 01a - Groundplate to convert the old battery base to the fit the univeral base
. part B0a - AA Battery base
. part B0b - AA Battery case (3x AA size)
. part B0c - AA Battery case lid
. part 02a - Tower low mod1 (replaces part 01, 02, 11 and 12)
- modifiction 01a (jan 2025).
Add two more options for battery bases an AAA and 18650 model.
. part B1a - AAA Battery base
. part B1b - AAA Battery case (3x AAA size)
. part B1c - AAA Battery case lid
. part B2a - 18650 Battery base
. part B2b - 18650 Battery case
. part B2c - 18650 Battery case lid
I build this model after i found the drawing from 1877 on internet and because the tower has some cracks in the onstruction it is pending if or when he will fall over, besides that I see the lighthouse every day.
Al parts are printed in PETG but PLA is also fine (just don't place the model in the sun).
Printer settings:
- 0.15 detail layer for parts 05, 06, 08, 09 and 10
- 0.2mm quality for the other parts
- infill 15%
- nozzle 0.4mm
- brim for part 02, 03 and 10 radar print upside down
- Support for Base & Batt section and lower section using enforced support
Options:
- Just build the tower without light;
. Print the parts 01-10 and glue the together, no need to print parts
. Print part 00a if you like to raise the model by placing it on a pedestal.
- Build the tower with the working light;
. Print all parts,
. Fist glue together part 03, 04, 05, and 06 then part 08-09 (place a piece of silverfoil between them to
prevent light shinging thru the roof) and 10 the radar.
. Don't glue part 07 on part 06 it have a snug fit, place Led (wires already soldered on) and place the glued parts 05-08 over part 6, glue after testing the light not before!
The following filament colors are used:
- Dark Red for the tower
- Beige ad Dark Grey for the groundplate and first base (colorchange)
- Transparent for part
- White for part 04, 06 and 08
- Dark red for part 07
If you decide to put the Lighting option in the tower you need extra:
Hardware:
- Led 5mm bright white or bright warm white (is more realistic)
- Resistor 33 or 47 Ohm (smd 1210 or 1206 version)
- ATTiny 13A, 45 or 85 dip version
- Dip 8 socket (bent legs to make surface mount version)
- Slide switch (micro)
- 3mm screw for the battery case lid
- Electrical wire approx 50cm red and black
- PCB is optional
If you decide not to use a PCB you can solder the wires directly to the ATTiny but;
Make sure to program your ATTiny first and test it before soldering wires to it.
Additional files:
- Electronic scheme
- Pcb surface mount layout
- Arduino sketch