VW Beats Subwoofer Upgrade (Jetta GLI and others)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This was deigned to replace the factory subwoofer in my 2023 VW Jetta GLI with beats audio.
- Ocena
- 0 / 5
- Polubienia
- 19
- Pobrania
- 74
- Wydruki
- 0
- Wyświetlenia
- 2409
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Audio
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This was deigned to replace the factory subwoofer in my 2023 VW Jetta GLI with beats audio. The factory subwoofer leaves a lot to be desired, this sub performs very well in this spot and is a simple plug and play drop in with no modifications required. You get to keep all the factory tools in place. From my understanding it will fit a lot of VW cars with the beats audio and perhaps even with the fender audio with factory subs in the spare tire well, you will have to do your own research. It produces a nice clean bass that I find I need to turn the subwoofer setting down to 2-5 for hip hop, rock, metal, or heavy bass songs and -4 for county songs. It's not going to get obnoxious wake the neighbors up and shake the glass loud but is very satisfying bass you can feel.
The subwoofer this was designed for is a Rockford Fosgate R2SD2-10 2ohm DVC, other subwoofers may work here (need to be 2 ohm DVC for best results) but they need to be shallow mount and airspace needs to be considered along with mounting holes, no others were tested.
Print Settings
- Printer brand:
Prusa
- Printer:
I3 MK3S
- Rafts:
Doesn't Matter
- Supports:
Yes
- Resolution:
0.3 and 0.4
- Infill:
20% Rectilinear
- Filament brand:
Any PLA+
- Filament color:
Any
- Filament material:
PLA+
- Notes:
I used a 0.6 nozzle for this project because it's quite large and I wanted to speed up the print times, you can use a 0.4 nozzle just fine, but it will take a while and 0.3 will be your max layer height. I printed the top and bottom pieces at 0.3-layer height and 4 perimeters for extra strength around bolt holes. The only supports needed are on the electrical connector on the top piece, I used organic, watch out on the inside where the wires and pins are inserted you won't want supports in there because they will be hard to clean out. The bottom is printed upside down due to the circle relief for the isolation rubber. The tube was printed at 0.4 layer height and 2 perimeters, I sliced the tube in 6 pieces in my slicer and printed them all in one print. This will take around 2 1kg spools of filament total.
Assembly
Printed parts:
The top and bottom are in 4 pieces each, they have pin holes in the sides for 1/4" all thread pins 1 1/2" long, you will need a total of 20 of these pins. Watch hole spacing during assembly to assure pieces are in correct spots. I used 2 part epoxy to glue together the pieces assuring to fully coat the pins are they were inserted and coating all attaching faces. I then used a long zip tie around the outside of the assembled pieces to apply clamping pressure while the epoxy cured overnight. The tube I assembled using (12) 8/32" all thread with nuts and washers on each end, each of the pieces will be approx. 8" long, will need trimming when done. After all rods are tight you will need to seal all seems with silicone (top and bottom + all joints on the tube where you sliced it) the box is to be air tight. Stuff with poly fill! Add a piece of rubber 1/8" thick cut in a circle to fit the relief in the bottom of the box, I used some from amazon with a self adhesive back.
Electrical connector:
You will need:
1- 4 pins (TE Connectivity 2-964296-1) best source for these is a site called digikey.com
2- 14 gauge copper speaker wire
Wiring:
If you are looking at the connector where the plug goes in from the front the pins will be:
(- - + +)
The first and the 3rd pins will be a pair and the 2nd and the 4th will be a pair. Attach pins to the wires, keep your pairs in the correct spaces and push them in from the rear. This can be a bit challenging; I have found if the pins get bent slightly, they won't go through. After crimping the wires on make sure the pins are straight in all directions, use a needle nose to get them started and a tiny flathead to push them all the way in. I filled this entire void with silicone to seal the hole.
Install:
Unplug factory sub, remove large plastic hold down nut from factory subwoofer, remove subwoofer, remove hold down screw by pushing down and twisting 90*, install new sub, and plug in! Done!
