Liczymy pasujące modele…
This printed center console cubby doubles the storage of your mk6 VW Golf/gti or mk5 Jetta. Simply remove your outdated MDI port, and snap this storage cubby into its place. Tight tolerances, durable side clips and the bottom locating peg…
For the dash vents. I suggest printing it side up with supports since the support side sits inside the dash anyway. Mirror it for the opposite side.
3D printable cold air intake for your MK6 VW 2.5! Unlock induction noises and enough placebo power gains to make your butt dyno say “It feel torqueier down low!” with this here 3d printed doohickey. Disclaimers: - While I have had no…
Ring adapter for 4 door speakers. Door bots with 5mm@10mm. (158mm standard door fixed bolts) Speakers fixed with drywall 5/8 (143mm diameter) Standard fix for 6in speakers.(not 6.25 or 6.5mm) ... Adaptador para VW GOLF, Jetta, Bora para…
Description Wiper blade aero spoiler designed for VW Golf Mk2 / Jetta Mk2 . This model has been tested on a VW Golf Mk2, but it may also fit other Volkswagen models using a similar wiper arm design. The project consists of two parts:…
Do you need this bracket? No--drill, home depot, and toggle anchors will get it done faster and maybe cheaper. Do you want this bracket? Well, that's up to you! This bracket snaps into the lower grill on a Mk4 jetta. You need to print…
I felt like making this replacement custom emblem for my Volkswagen Jetta… The font is “Red Rock”
This printed center console cubby doubles the storage of your mk6 VW Golf/gti or mk5 Jetta. Simply remove your outdated MDI port, and snap this storage cubby into its place. Tight tolerances, durable side clips and the bottom locating peg…
Developed this part for a co-workers clutch spring detent in his mk2 VW Jetta. This is the 6th and nearly finished version. He unfortunately no longer has the vehicle so we weren't able to finish it completely. The outer cylinder needed a…
It fits specifically for the Blaupunkt Palma 190 BT radio. The internal dimensions of the frame are 178 x 100 mm. Printed with black PETG on Bambu Lab P1S (0.08mm Extra Fine @BBL X1C preset). Infill - 20% Gyroid Wall Loop (Number of…
3d scan of the honeywell turbo that comes factory on the 2013.5-2015 volkswagen CPPA/CPLA engine
For the dash vents. I suggest printing it side up with supports since the support side sits inside the dash anyway. Mirror it for the opposite side.
3D printable cold air intake for your MK6 VW 2.5! Unlock induction noises and enough placebo power gains to make your butt dyno say “It feel torqueier down low!” with this here 3d printed doohickey. Disclaimers: - While I have had no…
Compatibility: Fits VW Golf III (1991–1998), Jetta MK3 (1992–1998), Vento (1992–1998) vehicles. Secure Mounting: Precision holes align with factory mounting points for snap‑in installation. No need for OEM rubber insert, Durable Design:…
This is a replacement part for the interior hood release handle bracket (VW part #1K1823633B), which connects the hood release handle and the bowden cable. If this part is broken, your hood release handle can't work properly, preventing…
Ring adapter for 4 door speakers. Door bots with 5mm@10mm. (158mm standard door fixed bolts) Speakers fixed with drywall 5/8 (143mm diameter) Standard fix for 6in speakers.(not 6.25 or 6.5mm) ... Adaptador para VW GOLF, Jetta, Bora para…
My Jetta's front rims (not original) lacked center caps. They are printed in two parts, minimizing the need for supports. The print surface is sufficient to eliminate the need for a skirt; however, this is entirely up to you. The logo can…
Printed on my Ender 3, PETG filament, 0.20 layer height. The finish is currently being improved for a better presentation.
easy tip In my case, the PETG filament I used is shiny and all the accessories and the rest of my car's dashboard are "matte", so I put a coat of matte black paint (spray) on it.
Custom dash kit to install a Sony XAV-AX3250 in a MK4 volkswagen Jetta (mine is from 2004, but I believe it should fit all MK4 Jettas, and potentially other VWs from the era). Is a toolless and screwless install. When printed face down…
This part is for vw mk4 users that uses grills withouth emblem I reccomend using ABS or ASA, PETG should work too.
This bracket will only fit the front doors spacing for a perfect fit of 6.5 speakers. NO VIBRATION , DEEP BASS. SETUP FRONT = (Bracket + RECOIL + 6.5 Speaker) REAR = (RECOIL + 6.5 speaker ONLY) I recommend getting these silicone from…
Vent cover with lamels, fits like glove. Supports only required for side spike triagle holders. Looks great and works wiVent cover with lamels, fits like glove. Supports only required for side spike triagle holders. Looks great and works…
I was rebuilding my shift box using a kit i purchased https://amzn.to/4mX65ee Everything was great minus the “1st-2nd slider” “Reverse lockout” was just dust in the bottom of the shift box. That means i didn't have a part to measure so i…
- Tapa cubre volante conocida como "Sandwich". - Compatible con Golf MK3 o Jetta A3 (1991-1999). - El modelo incluye una tapa superior y una inferior que se aseguran mediante dos tornillos. - Incluye un versión con textura (Mayor Peso de…
Rejilla de la salida de aire acondicionado lado derecho del copiloto Compatible con Volkswagen Golf y Jetta A3 (1991-1999) Funcional 100% Incluye las aletas y el eje que las mueve
My roof rack was leaking on my Mk4 Jetta wagon, and the foam gaskets aren't available anymore. Traced them out and then printed them in TPU. Set them to fully print each piece one at a time to avoid excess stringing. There are 3 files,…
Description Wiper blade aero spoiler designed for VW Golf Mk2 / Jetta Mk2 . This model has been tested on a VW Golf Mk2, but it may also fit other Volkswagen models using a similar wiper arm design. The project consists of two parts:…
This is a recreation of the official Rabbit grill badge that came on my 1987 Austrian domestic market Golf "Rabbit edition". For the clips to function right, you need to print this part on its side, as shown in the second picture. I…
This is basically a 1 to 1 recreation of the original cap covering the wiper nut. I recommend using a heat and uv resistant material, preferably something like petg. Sadly this part only works when printed on it's side, otherwise the clip…
This is a 1 to 1 recreation of the throttle body pulley on a 1.3 litre NZ VW engine. I strongly recommend using a heat resistant material, I personally used PETG and it has held up for multiple years at this point.
Do you need this bracket? No--drill, home depot, and toggle anchors will get it done faster and maybe cheaper. Do you want this bracket? Well, that's up to you! This bracket snaps into the lower grill on a Mk4 jetta. You need to print…
Mirror Adjuster control knob for VW Golf Caddy Jetta Scirocco Polo MK1 Mk2
Print with something a bit more heat resistant than pla (mine is pte-g) and put D profile window seal trim in it and it will fit your car.
Outline Pendant from a Volkswagen Jetta Mk4 or Bora Mk4 . I tried it for my first time to construct a outline pendant of my own car. Please be patient with my first constructed car
Knockoff emblems can be found on Amazon, eBay, or Aliexpress for around $10. You can also pull a hatch emblem from the parts yard. If you can't procure a replacement hatch emblem for a reasonable price, you can print one of the included…
Ersatzteil für OEM nummer 1J0823593C gedruckt in 0,15mm layerhöhe 31% infill auf einem i3 Mega S
Cup holders for your MK1! This uses the cabriolet style shift boot, kinda. I also made the cup holes a little small, it fits a can tightly. A water bottle will fit, but the tapered mcdonalds cups or anything else probably wont. It's not…
The phone clip is designed to hold a Pixel 6a wearing a Google case, but it will also hold a Pixel 4a in a generic case. I printed in PETG because I was concerned that vibrations might be an issue. The phone does wiggle a little while…
If you found my things useful, you can buy me a cup of coffee: paypal.me/FirmaOnbenul Zijdeur/spatbord/achterpaneel Trim Moulding Strip Auto Fasteners Plastic Clips voor VW/GOLF/MK1/Jetta als pen gebruik je een stukje 1.75mm filament Side…
My cup holder has been meticulously designed to fit seamlessly into the available space in the Jetta A6 2013. I have taken aesthetics and functionality into account, ensuring that it's an elegant addition to the interior of this iconic…
My toddler stole my old knobs, so I made a made these replacements. Printed in Polymaker Polysilk Silver with Octagram Spiral surface pattern
I designed the basic dimensions based on the 191 819 707 C or 191 819 719 B (Both are written on the same part), feel free to remix it to fit a gauge for example, sadly the “max” hole size is 45mm but you can probaly get up to 49mm with…
Want a manual style shift knob in your automatic mk6 or mk6.5 VW? Look no further! Shift knob adapter for automatic style transmissions to adapt a different, or in my case, more comfortable shift knob. Simply pull the shift knob…
I made mud flaps because buying them is way too expensive, and non of the options look subtle enough. Printed with TPU with 1mm nozzle, 100% infill. Tested in all weather conditions for a full year, from +40C to -40C, on gravel, sand,…
I designed this cabin filter housing for the Golf MK2 or the Jetta MK2 since there is no perfect model available. It's designed as the original so it should fit in every Golf etc.
My favorite model of the VW Jetta, the MK4. Adjust the height to your needs, and I suggest to print the side you would like displayed down. Hope you like it!
*Updated on 6/24/25 - Added specific versions for FDM and SLS. I went into my car the other day and noticed that my sunglasses compartment was down and wouldn't close back up. It wasn't hot out, and I rarely have sunglasses in it, but one…
0,2mm layer height 0,4mm Nozzle X dimension = min. 60mm Happy printing.
This was deigned to replace the factory subwoofer in my 2023 VW Jetta GLI with beats audio. The factory subwoofer leaves a lot to be desired, this sub performs very well in this spot and is a simple plug and play drop in with no…
Just a quick model I made to adapt a 76mm cone filter to the stock MK7 Jetta intake hose, tested it for about a week now and has been all good so figured I would post it, works great and sounds good and my IAT's are about around the same…
I made this Cubby Organizer for my VW Jetta ‘17. It fits snuggly in the empty space under the radio. I like to keep a few small items on-hand but they’re constantly getting shuffled around. This simple organizer helps keep everything…
Getränkehalter für VW Golf 2 / Cupholder for VW Golf Mk.2 / Jetta 2 Ersetzt den originalen Aschenbecher. Diesen einfach herausziehen und den zusammengebauten Getränkehalter einschieben. Stört nicht beim schalten und die 12V Buchse ist…
