Creality K1C , K1 , K2 , K1 Max Recirculating HEPA Filter (v2)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Afilter solution for the K series by Creality, should fit all the K models with its low profile design.
- Ocena
- 0 / 5
- Polubienia
- 39
- Pobrania
- 112
- Wydruki
- 0
- Wyświetlenia
- 3687
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Creality Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
Welcome to a few days of my life!
V2 is now live with a more modular system!
This is my version of a recirculating filter for the K series printers by Creality.
This design was made to be modular, allowing you to use affordable HEPA filters as well as be easy enough to print even with semi-bad tolerances (this was designed around my 0.2 tolerance limitations on my K1C) AND using more carbon and carbon foam to filter air inside the chamber.
Hardware needed:
No fastners or magnets needed but you will need a 120mm radial fan, the same model as the side cooling fan in the K1C printer by default. The fan is a 12032D and the 24v can be spliced into the same power line as the fan already in the printer (how to can be found on DerrickDarrels GitHub, thanks buddy!). Fan can be found on ebay.
Filter needed:
Samsung Cyclone Force SC21F50HD H12 HEPA filter for a vacuum cleaner. I found mine on ebay and designed the filter section for easy modification should this not be available in your country.
Design considerations:
This was designed to be modular so the duct can be adjusted or the fan section changed for more available HEPA filters. On larger printers you should even be able to add another section for some carbon should you wish.
After reading on the potential dangers of some filaments in terms of airborne contaminants I decided a proper filter was needed. Nothing else available was suitable as they either used axial fans which cannot provide enough static pressure to make it work OR they rely on underpowered fan solutions OR they bring air into the chamber or remove air which means we change the chamber temps which is a HUGE no when printing complex designs with exotic filaments.
This design purely filters the air in the chamber using HEPA/Carbon to capture some of the pollutants which would normally leave the printer (a big no no in a office like mine). This design is NOT made to provide more cooling to the chamber or print.
Changelog - - -
V2 - simplified basic HEPA filter to 2 section system with NO connectors needed. Fan now fits perfectly as well. Mid section possible for carbon filters as well (in progress)
V1 - launch with 3 sections and clip system to connect
>>>>>V2 variant - - -
Print details:
All parts van be printed on PLA.
- Filter Section (V2) -
- Print on its back, flat section
- 0.16-0.2 layer height is good
- SUPPORTS needed, but recommend default supports in Ocroslicer, for those not using the excellent supports in Orca. Would recommend manually painting on the supports for the entire inlet section not just where they are automatically placed. Doesnt add risk or much time to the print.
- Fan Section (V2) -
- Print flat on its back
- 0.16-0.2 layer height is fine, use variable as this works as well and speeds up the print.
- NO support needed
These sections should clip into each other, otherwise just use a tin bit of glue or bluetak AFTER fitting the fan!
>>>>>V1 variant - - - Removed
Assembly:
Add fan to Fan Section using double sided tape on the rear plate (thin tape is good), mid section should locate via the fan outlet and ridge on the left side of the design.
Filter section should be nice and snug when clipped onto the duct/mid section then just use connectors to slide into the clamps on the sides, filter and fan sections are connected and mid is kept in place using pressure. This can be fiddly, I will iterate on this to make this a better, easier connection.
If you want to seal anything, just use some bluetack (very thin between sections).
Please please please post your makes or tell me if you have ideas for this and I can work on those OR show me a remix, would love to see how people modify this.
Sidenote - you dont have to use the clamp system if you dont want to, just use some hotglue (on a low setting) to seal and attach the parts. NOTE, you wont get the fan in if you connect it all first, fan needs to go in first!
If you want V1, drop me a message and Ill share the files with you.