BenchTop Disc Sander / BOSCH blender CNSM10 / 12.5 cm disc sander
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a disc sander with electronics taken from BOSCH BLENDER type: CNSM10 (E-Nr: MMB21P0R/01). THIS IS NOT A TOY!
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 15
- Wydruki
- 0
- Wyświetlenia
- 271
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Share Alike
THIS IS NOT A TOY AND CAN BE DANGEROUS!
This model is mostly supportless & can be built without taking the electronics apart (no need to de-solder electronics).
UPDATE LIST & EXPERIENCE:
So I tought that the motor was exclusively built by BOSCH - I found the motor separately:
- U8916 motor for Kenwood BLP400/402WH blender:
https://www.miss-pieces.com/moteur-pour-blender-kenwood-blp400wh-blp402wh__p252756.html - MOTOR U8916 PRE BLENDER DELONGHI KW716888 MODELS: BLP400WH BLENDER BLP402WH BLENDER
https://www.pigmento.pt/index.php/produtos/centrifugadoras-e-liquidificadores/motor-assembly-u8916-p-liquidificador-delonghi.html

I highly advise to be under supervision, even better with someone with knowledge of electronics.
Diameter of the DISC_HOLDER is 12.5 cm - made for standard sanding discs.
(If you want different size, just write a comment I'll do it.)
Whole kit printed on PRUSA MINI+.
The .Gcodes I provided have 4 wall perimeters for better sturdyness & 15% Gyroid infill.
THE ONLY EXEPTION IS THE V2 DISC HOLDER - THIS HAS 2 WALLS & 15% CUBE INFILL to be as light as possible.
Hardware used:
- It doesn't matter what shape of screws you use - you can use HALFROUND / SOCKET type
- FRONT_PANEL REQUIRES either original screws from the blender itself, but you can use basic M5x8mm screws to secure the blender electronics.
- BODY_LOWER: 4x screws M5x12mm (12mm is minimum size, but you can use longer screws if needed.)
- BODY_TOP: Requires 2x M3 NUT + 2x screws M3x8mm
- FEET: 14x screws M5x8mm (8mm minimum size, can be longer.)
- FAN_COVER: 4x screws M5x12mm (12mm minimum size, can be longer.)
- DISC_HOLDER_GROOVES / DISC_HOLDER_NO_GROOVES: 2x M5 nut + 2x screws M5x20mm
- V2 FLAT_DISC - 2x screws M5x20mm + 2x M5 nut + 2x screws M3x20mm + 2x M3 nut
- Raw 1.75mm filament for 3D printing / toothpicks (this is used for hinges at feet & the body itself)
OPTIONAL TOOLS:
- M5 screw tap / M5 thread drill
- Electric screwdriver
- Hex bits for M5 + M3
- Hot glue gun (advised) / CA Glue / any instant glue
- Any size of zipties (1-2 small ties)
- Soldering iron + tweezers + WAGO connector (the blender itself has a limit switch, so it won't accidentaly start spinning without the lid - we will get rid of it)
- 4x Felt Pads (or just print them in TPU so it won't damage your table)
STEP 01:
Prepare necessary parts and hardware. Check if you are missing something.

Dissassemble BOSCH Blender TYPE CNSM10:

(other codes & info)
E-Nr.: MMB21P0R/01
FD: 0006
Z-Nr.: 701274
220-240V ; 50-60 Hz ; 500W
Illutrative photo of what to expect inside (don't cut off the power cable / cable plug):

STEP 02:
Cut off limit switch under the lid and solder the wires together or use WAGO connector. (This is a safety switch - the blender won't start without the lid on. We will bypass this safety function by connecting the wires together.)
After completing the whole assembly, you can start the sander by the round knob on the side.

STEP 03:
Optional: Hotglue FRONT_PLATE + FRONT_RING together.

Screw Blender motor together with FRONT_PLATE (4x screws M5x8mm).

STEP 04:
Optional: Use M5 Screw tap to adjust the screwholes to correct size.

Screw FRONT_PLATE + MID_RING with BODY_LOWER (4x screws M5x12mm).

STEP 05:
Now we will use hinge to secure BODY_TOP + BODY_LOWER together - fit 1.75mm filament through the hole. Try using tweezers if the filament gets stuck.
OPTIONAL: You can use toothpicks as they have sharp point - they slide in easily.
Cut off excessive material.

STEP 06:
Let's add 2x M3 nuts to BODY_LOWER, so we can securely screw the unit in later steps.
Test if the hinge works and the body halves can be closed.

STEP 07:
READ BEFORE CONTINUING THROUGH THIS STEP!
Add a bit of hotglue on each part of the SWITCH_COVER, pay attention to the D-slot rotation - the cutoff is on the left side.
Quickly press the two halves of the body together and adjust the rotation on the switch covers if needed.
The pressure will straighten up the SWITCH_COVER.


STEP 08:
Fit the actual switch through the slot we just finished and screw the parts together with 2x screw M3x8mm.

STEP 09:
Let's add something to hold our cute disc sander in place.
Screw 2x LEGS pieces together with BODY_LOWER by 14x screws M5x8mm.

Connect 2x FEET pieces together with 1.75mm filament. Cut off the excessive material.

OPTIONAL: Add felt pads or rubber pads under the FEET for better traction and damping.
STEP 10:
Optional: Use M5 Screw tap to adjust the screwholes to correct size.

We are almost finished - speed up!
Rotate the BACK_SPACER so the slot is straight down - Fit the power plug through the slot (a little tricky, but it can be done).
Let's connect the FAN_COVER with BACK_SPACER + BODY_LOWER by 4x screws M5x12mm.

STEP 11:
Add final pieces together like the SWITCH_KNOB and 2x M5 nuts + 2x screws M5x20mm to DISC_HOLDER.
OPTIONAL: Instead of glueing the Sanding discs to DISC_HOLDER, you can use hot-glue VELCRO (hook & loop tape), it also works.
V2:
The FLAT-DISC has better weight distribution and provides additional security with M3 nuts & screws - essentially, it means it's has no wobble and no vibrations.
Place M5 nuts in bigger slots and M3 nuts in the smaller slots of the disc holder.
Fit 2x screws M5x20mm + 2x screws M3x20mm into correct nuts and screw them through the nuts to the shaft.
OPTIONAL: Pour a little bit of hotglue on the secured nuts and let it cool down. This will secure them even more if it still has potential speed and vibration.
When fitting the FLAT-DISC it is necessary to take your time and force it a little bit on the motor shaft.
Best way to do this is to fit it on the shaft as much as it allows and take it off again and again.
!FOR YOUR OWN SAFETY - TEST THIS MONSTER UNDER SUPERVISION!

STEP 12:

Enjoy! (This step is mandatory).
Any questions? Ask me in the comments. I visit Printables regularly.
If you have any suggestions, let me know. I can do similar models if you provide screenshots.
Be creative :)