Pikachu Light Stand
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
2,59 € – 3,16 € netto (bez VAT)
Dla pliku: Stand_0.2mm_PLA_MK3S_2h58m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 2,88 € netto (środek widełek).
- Masa podana przez autora
- 34 g
- Czas druku podany przez autora
- 2,97 godz.
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Pikachu powering a Lamp
- Ocena
- 5 / 5
- Polubienia
- 209
- Pobrania
- 920
- Wydruki
- 5
- Wyświetlenia
- 6436
- Oceny
- 3
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Sculptures
- Licencja
- Creative Commons — Attribution — Noncommercial
I needed a present for secret Santa in my girlfriends family and knew that she liked Pokemon and Pikachu in particular. So i made her a Lamp "powered by Pikachu”.
i will include my g-code file put please just use it as reference and slice it yourself!
Printed with PLA in 0.2 layer height, 0.4mm nozzle and 8% gyroid infill. I auto-generated the support with Prusaslicer and painted over the ears so they don't get supported (its not needed and they come out perfect).
I paused the print at Layer 70 to add sand to weigh it down a bit (DO NOT fill it up too high leave 5-10mm, otherwise the filament fan will blow it out again! i learned the hard way) because i wasn't sure if he would tip over with the lamp attached.
Afterwards i glued the tail on with superglue(its easier to print seperate), spray painted it with a few layers of primer, painted it with acrylic colors and sprayed on a few layers of clear coat so the paint layer is protected.
After it dried and you are happy with the result you can glue the base plate and Pikachu together (i used superglue). Watch out! → make sure the holes on Pikachu's bottom and the stand line up and you don't glue it on the wrong way!
Next steps:
I accept no responsibility nor assume liability if you harm yourself, it should be disassembled/reassembled by a professional!
- disassemble the lamp (i used THIS ONE) so the cord and the lamp head is separate
- push the cord trough the hole from under the base plate trough the Pikachu
- reassemble the lamp
- from below, push the lamp head through the ring Pikachu is holding
- secure it with the ring for the outer thread that is included in the files (it was designed for IKEA TRÅDFRI lamps but it may fit others as well)
- pair the remote if you use a TRÅDFRI RGB
- enjoy your new lamp!
Hope you like my design, if you did please leave a like and/or comment.
would be interested how yours came out so please feel free to send pictures/post a make!
Have a great day and Happy Holidays!