1 / 5
Tilting License Plate Holder for 1UP Bike Rack — zdjęcie 1
1 / 5

Tilting License Plate Holder for 1UP Bike Rack

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Stops your plate from hiding behind your bike rack!

Ocena
5 / 5
Polubienia
22
Pobrania
116
Wydruki
1
Wyświetlenia
1585
Oceny
2

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

Why?

If you have a 1UP rack there's a 99% chance your license plate is obscured. I know that's bad, but I wasn't about to pay $125 CAD for the basic plate holder from 1UP. Instead, I made this!

 

Read Me

Something something provided as-is, without warranty, etc. You don't want your plate flying off and possibly hitting someone so assess risk accordingly. I'm personally confident in the strength of this model for my own needs but it's up to you to make sure you feel the same way since you're the one that's liable if anything happens.

This holder may not be legal in your jurisdiction since it doesn't shine a light onto your plate. On the other hand, it's probably better than it being completely obscured like it is now so I'll leave that to your discretion.

 

What Plates Are Supported?

I'm from British Columbia, so I know for sure it fits BC plates. But I understand that all North American plates have the same mounting footprint so any 6"x12" (150x300mm) plate should fit.

 

Required Hardware

Pivots

  • 2x M5x12 BHCS or SHCS
  • 2x M5 10mm diameter washers
  • 2x M5 nylon lock nuts

Pins

  • 2x M5x20 BHCS or SHCS
  • 2x M5 nylon lock nuts
  • 2x 10mm OD/15mm free length/0.8mm wire diameter springs
    • The design is a little flexible as to what springs you use so feel free to try if you have something close lying around already.
    • Untested, but these may work

Plate Holder

  • 4x M5 heat-set inserts (7mm diameter, 5mm length)
  • 4x M5x10 BHCS or SHCS
  • 4x M5 washers (required diameter may vary based on your plate and what screw type you use. Possibly optional)

Misc.

  • Blue threadlocking compound
    • See important warning in the “Material” section below
  • 2x 1UP-compatible mounting bolts
    • I didn't want to pay $65 CAD for extra security bolts from 1UP so I used some standard ½" 13TPI 1-5/8" SHCS. I used 1-½" length instead. Check your local hardware stores/auto parts shops/machine shops. Get something corrosion resistant and consider using an assembly compound like ParkTool's ASC-1 on the threads

 

What To Print and How To Print It

Material

Use a filament that's UV resistant, can withstand heat, and is relatively strong. PETG, ASA, ABS, or even PC are all great choices. Some PLA+ blends might work, but personally I'd skip PLA entirely. I used ASA.

⚠ THREADLOCKER WILL DESTROY ASA/ABS ⚠

Do not allow liquid or paste threadlocker to touch ASA/ABS parts. It will cause them to crumble and fail. If you're concerned, use PETG

Slicing

All STLs are oriented the way they're meant to be printed. That may seem odd when you look at them, but this is a deliberate choice based on things like the direction of forces or minimizing warping.

Print it strong. 4+ walls, 20+% infill.

No supports are needed whatsoever. If you use a material that shrinks (ABS, ASA), ensure your shrinkage compensation is dialed. One of the optional parts is 300mm long and that can easily be 2-3mm out of spec without compensation.

What Models Do I Print?

There are several variants to choose from, but you actually don't ultimately need to print many models.

Each full plate holder has three components: a backer, two moving elements, and two spring shrouds. Here's how you pick what to print:

  • Backer. Print one of:
    • Full-width if you can, but you need a big print bed (300mm+). Use an aggressive brim because you don't want this thing to warp. Or;
    • Split. Print a left and right backer if you have a smaller printer
  • Left and right moving elements. Print one set of:
    • 2-position. This shows your plate in the fully-up or fully-down rack position (0º and 90º). Use this if you rarely use the middle rack position. I suspect most people will want this one. Or;
    • 3-position. This has stops for 0º, 45º, and 90º. Works if you use the middle position of your rack.
  • 2x spring shrouds. These don't have any variants

Assembly

The CAD files also model the hardware (except the springs) so you can check that for a reference.

Preparation

  • Press M5 heat-set inserts (4 total) into the “mounds” on the two moving elements

Pivots

  • Place an M5 nylon lock nut in the hexagonal recess of a moving element
  • Place an M5 washer on an M5x12 machine screw. Push it through the smaller hole on the side of your backer
  • Place the moving element and backer together, threading the screw into the locking nut
  • Tighten until parts are stable but can pivot freely. The machine screw should be just barely proud of the nylon lock nut
  • Repeat on the other side

Pins

  • Place a spring shroud on an M5x20 machine screw. The head of the screw should rest on the “top” of the shroud
  • Place a spring over the machine screw and into the spring shroud. When you're done, it should be a sandwich of screw head > shroud > spring. One of the pictures above shows what I mean
  • Place this assembly through the larger hole on the side of the backer. The thread of the screw should be pushed through the slot in the moving element. If you've assembled it correctly, the spring should be pushing against you at this point
  • Place an M5 nylon lock nut on the thread that's poking through the moving element. Tighten only until the bottom of the screw is just barely proud of the lock nut
    • PROTIP: this can be a pain to thread on. I find it easiest to start the nut by hand, then place the moving element halfway between two stops. At that point you can let go, use needle-nosed pliers facing inward to hold the nut, then thread the screw in with a hex key
  • Repeat on the other side

Licence Plate

  • Apply blue threadlocker to 4x M5x10 machine screws
    • ⚠ THREADLOCKER WILL DESTROY ASA/ABS ⚠
  • Mount your plate to the moving elements using the prepared machine screws, optionally using washers if your combination of screws and plate require it

 

Tagi