SURV 7-in-1 survival companion
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Your ultimate 7-in-1 SURVival companion.
- Ocena
- 0 / 5
- Polubienia
- 32
- Pobrania
- 50
- Wydruki
- 0
- Wyświetlenia
- 1378
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Gadgets
- Licencja
- Creative Commons — Attribution — Noncommercial
Your ultimate 7-in-1 SURVival companion.
What can fit inside?
- water fliter for water purification
- multi tool knife
- flint fire starter
- first aid emergency kit
- emergency whistle
- compass
- solar phone charger
Be safe wherever you go and keep all your emergency gear safe at one place with SURV.
Print settings:
Printer: VoxeLab Aquila X2
Slicer: PrusaSlicer
Layer hight: 0,3 mm
Infill: 20%
Nozzle: 0.4 mm
Material: eSun black and white PLA
Default printing speed for PLA
Nozzle temperature: 200C
Heatbed temperature: 60C
No supports. Supports only on electronics holder.
For better adhesion I used textured plate and with glue.
For the upper part I used thicker walls for extra strength and better print quality because the printer then prints the 3 mm wall as one wall in circular shape and avoids fast and small zigzag movement wich lowers the quality.
In the slicer you only need to spearate the logo and print it as two different models. First print SURV logo in one color without skirt or brim and when the print finishes change the color and start the print of the upper part. Or print it in multi color slicer settings if you have a multi color printer like Prusa with MMU upgrade.
The same principle goes for the version with solar charger where the logo is on the solar charger holder. For the version with solar charger I recomed that you split the solar charger holder inside the slicer and print each part separate.
Instructions for assembly:
The assembly is very easy. There are two avalible options - with solar charger and without charger.
For the option without charger you just put your gear in their designated places by shape, close with the upper part and put the compass inside its place.
For the option with solar charger you only need to put together the charger holder which is very easy and takes you about 10 minutes. All the parts are putted together at their designated places using connectors. I also used a little bit of glup to be extra safe.
1. Disassemble your solar charger, just separate the charger using a knife in the middle (you will see a line in the middle of the original case from the carger).
2. Unscrew the electronics (save the screws).
3. Scew the electrnics holder on the electronics with the same screws.
4. Put the whole solar charger with electronics inside the printed holder (it will fit tight and be carefull with all cables)
5. Put the electronics part with holder on its place on the upper part and glue it together (you have a few cm of cables so you will have enough place for your fingers from the electronics part to the solar charger that is inside the printed holder.
6. Put the solar charger holder part with the solar charger inside on the upper part and glue it together.
7. Put the compass and cover of the solar charger on top and glue it together.
FINISH!
Location of photos:
Big Almaty Lake, Almaty, Kazahstan
Photographer:
Mateo Milicevic (me)
List of gear inside:
Solar charger:
https://www.amazon.ae/dp/B0CQQMB6V7?ref=ppx_pop_mob_ap_share
Multi tool knife:
https://www.amazon.ae/dp/B09QQBC78C?ref=ppx_pop_mob_ap_share
Compass:
https://www.amazon.ae/dp/B09YYFVV47?ref=ppx_pop_mob_ap_share
Water filter:
https://www.amazon.ae/dp/B0CN9DXS92?ref=ppx_pop_mob_ap_share
Flint fire starter:
https://www.amazon.ae/dp/B0C36BF739?ref=ppx_pop_mob_ap_share
First aid kit:
https://www.amazon.ae/dp/B0CN5P2Q51?ref=ppx_pop_mob_ap_share
Whistle:
https://www.printables.com/model/606419-extremly-loud-whistle